When i finsh load ArduPilotNE to borad and the motor keeping runing is it corrrect
i load ArduPilotNE to borad the motor keeping runing.
Read more…
1 Reply
All Discussions (17288)
Sort by
FailSafe MUX Pins
I had just purchased a FailSafe MUX board. However, I am not sure of the pins and their usage in the board.Please advise.
Read more…Is the uav DevBoard suitable for this project?
Hi everyone,I want to build a hydrofoil sailing boat based on this hydrofoil windsurfer, but to use the UAV DevBoard and moving weights to stabalize pitch and roll instead of the riders body mass.I have only looked over the website breifly and am una
Read more…Geophysical Platform
I wish to develop a platform for geophysical work. The problem is that suitable geophysical receivers are copper coils with a weight in excess of 5kg - with ancillary electronics the total payload would likely be 10kg.In addition, an air coil receive
Read more…Do I need change" Text code "and "main code" to run a 3ch Rc car
I am new here and i want to built a 3ch RC car to for using ArduPilot 2.1.So do I need to change code to Run the car? Do i also need XY sensor and Z sensor ? (sorry my English is not good)
Read more…Plans ArduPilot
Hi, i have recived my ardupilot hardware today.I have looked on the homepage but i can not find a instruction how to complete the construction (where to solder the gps, the usb interface the shield, servos ec.) I found a instruction how to solder the
Read more…locosys gps without airsensor and z sensor + added little features
hello ,i'm very new with C programing and arduino environment but i found out how to use the 2.2 soft with the locosys GPS (NMEA) so i wanted to tell you how i've done:in the Ardupilot_easystart_v22 tab change that to get nmea mode:#define GPS_PROTOC
Read more…need ur help guys to build a Quadrocoptor
I have seen the Quadrocopter the first time in Hannovermesse and it became my new passion, I want to build one for my graduation project. i'm a fourth year mechatronics engineering student living at the moment in Germany.I'm facing a huge problem in
Read more…A challenge: build a rainforest canopy exploration system
Hi all,We've recently been selected by a major funding agency to conduct a project aimed at reducing deforestation in the tropics. Given our first success, we want to participate in the next call for proposals, with an even more ambitious project.At
Read more…Infrared sensor vs ultrasonic sensor
Hey everyoneCan someone please help with some info on IR and ultrasonic sensors?Which is the better opsion for rangefinding at about 10m in terms accuracy and price?
Read more…newbie silly mistake, could you help?
hello all ,i'm very new on the ardupilot , i useally burn some pic, but in basic (proton ide)i had a similar project but with a 18f2550 pic but i guess the ardupilot is way faster than my soft i had some timing issues (but the soft works)i wanted to
Read more…My UAV DevBoard Project
Hi,My autopilot is the UAV DevBoard from Sparkfun. Mine is the "old" green board which is now superseded by this red board http://www.sparkfun.com/commerce/product_info.php?products_id=9038I'm posting this in the hope that others will share their exp
Read more…IR sensors affecting pitch trim.
I was viewing RCgroups UAV pages and came across this statement:"Beamer, I suggest putting the IR on the bottom or else your pitch trim will change as the sun heats your wing."I've experienced pitch trim changes that I couldn't account for and this m
Read more…ATMega168 and airspeed sensor
I am working with the ATMega168 version of Ardupilot (s/w version 2.1.2). I believe this configuration can support the airspeed sensor but am not 100% sure of this. I know that digital pin 8 must be connected to MUX IN 3 but where would the signal li
Read more…Easy glider UAV: List to do
Hey there,I found some useful info on this site. And i got a global idea of what i want and need. And please correct me if i am wrong.So i got this easy glider. List of what i need: ArduPilot 2.0, auto pilot, co-pilot, gps sensor, connectors for the
Read more…GPS and Barometric altimeter accuracy
Hey eveyoneCan someone maybe tell me wat GPS's are used in the paparazzi and ardupilot and how accurate they are in terms of lateral movement and hight, and also the accuracy of the altimeters on these two autopilots?Thanks
Read more…How many start their UAV project but fail to complete?
How many start their UAV project but fail to complete?
Read more…question about adjusting Ardupilot
I tired my freshly built Ardu pilot today. I turned on my flight stablizor and then the ardupilot. When turned on the Ardu pilot in way point mode the plane immediatle went in to a turn and dive. Fearing for the life of my airplane I quickly turned t
Read more…Flying Wing, SketchUp Planes?
I want to build my own airframe and was looking at doing something like what I saw below,http://diydrones.com/profiles/blogs/uav-flying-wing-scratchbuiltI don't want it to have any RC controls, just run a preprogrammed flight plan after launch and re
Read more…ArduPilot Boat Requirements
I'm going to be working on a boat that I'd like to have controlled by ArduPilot, and I have a few questions.First of all, are these the major parts I need? (breakaway headers and small pieces, I have) I was reading about needing sensors, not needing
Read more…