I'm running an APM 2.6 clone, which was fine on 3.1.5 firmware. I misguidedly upgraded to 3.2.1 last week and did an autotune with horrible results.
I want to revert back to 3.1.5 firmware, but in MP latest, if I try to download ealier or custom firmw
Read more…Hi !
I have a Tarot 690 hexa controlled by a NAZA V2, according to my knowledge this is already over the máximum limit for that autopilot. I want to install my new pixhawk in that frame. I could not find anywhere what size frame are the máximum that t
Read more…Hi,
Today i went to a field to try mode circle. Everything ok, quad does a good circle in 3 opportunities, but he did not look to the center of the circle. He all the time was parallel
Any idea will be welcome
Thanks
Martin
pd: I attach .txt archive in th
Read more…I put an ext compass to my APM on the tall gps mast under the gps but I can move a little from side to side with my hand; that it can affect compass? where or how is the best place to fix it?, time to time the copter yaw a little I'm not shure if it
Read more…Hi,
During a quadcopter autotune which started very good, I had passed the roll tuning phase and the quad was in the middle of the pitch tuning phase. I recentered the quad a few times. Until I had apparently the bad idea of correcting slightly the ya
Read more…Hi,
I've found a lot of information in the wiki and in these groups but I'm still trying to figure out a 'part list' to buy for an "assembly and fly your first quadcopter summer project" I'd like to plan for August.
I'm inclined to buy an assembly kit
Read more…Hello, I've recently run into a problem with the RC transmitter for my X8+ (TH9X). The copter flies fine (after a recent ESC and accelerometer re-calibration) but I am not getting any battery readings on the transmitter. All the battery readings have
Read more…My asymetric quad flies really well with an APM 2.6 on Copter.3.2.1 and MP 1.3.25.
But I've noticed that there is a slight roll twitch when I switch from any other mode to Loiter. Just once.
Otherwise rock solid in loiter, and responsive in stabilised
Read more…Hi,
could you kindly report and provide me with details of known to you Drone Fly Away cases to let me find a smart fix to meet FAA standards ?
darius
manta103g@gmail.com
Read more…Hi all.
I'm considering stepping up to 4S from 3S batteries, and wonder what is the accepted way of transforming a 15v nominal supply so that on can use equipment designed for 12v supply? Video Tx, LEDS, gimbal etc.
Best.DP
Read more…I have a 3DR DIY 2014 quad and I want to make it into a FPV racer.. any suggestions
880kV Motors
Pixhawk + GPS
X8R Taranis Transceiver
20amp ESCs
3300 mAh battery 35C
10x45 Props
I have FPV Fatshark Predator V2 goggles and transmitter
I am confused with a few things. I am wanting to purchase a copter capable of carrying a GH4 camera but using a Pixhawk. Here are the things my googling has failed to answer for me:
1. Is there a Pixhawk-based platform equivellant to the DJI S900? I h
Read more…Hello All. I have a quadcopter and am not sure if my batteries are no good or that maybe I am expecting too much. I have been sorting through my batteries, categorising them by run time to when an auto land occurs. I have the battery failsafe set low
Read more…Hi,
Have recently built up an Octocopter, which is using a 3DR pixhawk with 3.2.1 and has been calibrated (compass MOT etc), auto tuned and generally is running really rather well, but for one issue, YAW whilst in automatic mode.
The below graph shows
Read more…I have just setup a new quadcopter using the Tarot Iron Man 650 Carbon Fiber Quadcopter Frame. I have also added a gimbal.
The quadcopter howers at a PWM of about 750. This is the max recommended per the arducopter instructions. I set the THR_Mid opti
Read more…I'm a contractor and have seen table saws that can detect contact with a human finger / hand and cut the motor power instantly. It uses a current sensor similar to what you see in your kitchen and bathroom outlets aka GFCI outlets. That wouldn't work
Read more…eCalc estimates for throttle @hover have grossly changed in recent versions at least for my KDE 2814XF-515 motors.
According to eCalc throttle @hover should be 65%. In reality it averages ~45% with the exact same configuration as shown below. When fir
Read more…Hello,
I am looking for a sturdy digital camera mount for a quadcopter that doesnt have a gimbal. I just want to lock it at 30 degrees pointing down. Simple. The quadcopter i have is this.Ideally if it fits onto this, that would be great.
Something lik
Read more…Hi,
Does anyone know if this works or if there is newer firmware. From reading the comments there are issues ?
https://www.youtube.com/watch?v=7Nqr4-cbyvI
Read more…