Hi ppl
I was wondering about this props :
They have them as CW and CCW , are there any advantages/disadvantages to using this kindof props in a Quadcopter ?
Ivied reed in some forms that they are not so noisy and better for takeoffs ( i supposethey war
Read more…Hi,
Just wondering if anybody has noticed any improvement in stabilisation performance, particularly reduction of occilations with the use of High speed servos?
Cheers Paul
Read more…I am currently using the Ardupilot 2_7 program and currently trying to read the ground_course value for my bearing indicator.
Some questions:
Hi, I am wondering if anyone out there has flown the 98" MQ-9 Reaper from nitroplanes. Looks awesome and I plane to have this as my FPV drone. There will be some mods like a better paint job and clear dome for camera. Anyway I want to know if this is
Read more…This is my first version of an autopilot.. It uses a arduino, a range finder for aided precision on landings, 2 freescale pressure sensors (one for altitude and one for speed), a Locosys LS20031 GPS module, a 3-axis accelerometer, 2 axis gyro(XY), a
Read more…Hi all! (:
I currently able to test the XY and Z sensor accurately outdoor.
I am currently testing the sensors using
This is how I mount the sensors together with the AP on this piece of foam.
And to get accurate values with accurate degrees of tilt,
I b
Read more…I am wondering if there is a proprietary binary code output from the compatible Arduino GPS chips, or if an NMEA output is fine? This is because I want this magical GPS unit onboard: http://www.sxbluegps.com/sxblue-gps.html
Has anybody got a good fel
Dear Friends,
I have a problem when setup ArduPilot.
When the mode is moved to stabilize or fly by wire A, the throttle is always spinning fast and can not be controlled. I try to do debug in mode 8 (from Jason), and I see the value of Throttle always
Hi There, I am getting started on my first FPV drone and still have little knowledge on the electronics. I have purchased the Dragonlink TX module for my Futaba 9CAP radio. I have also locked in on a purchase of a 2.4Ghz 1 watt video/audio TX and RX
Read more…Hi,
I've read through a few discussions on this forum about poor man's DGPS and getting relative accuracy down to the ~1m range. It seems no one's having much luck even with identical GPS units. I'm wondering if anyone has manged this and what are your
Read more…Hi all,
i'm looking for Low cost Fiberglass, can someone help me!
thank you.
I-have-an-8ch-TX-flying-6ch-RX-radio-issue?
All-is-well-in-Manual-Mode.
In-Stabilize-or-FlyByWireA-the-control-surfaces-dance-with-travel-between-an-eighth-and-three/eights-inch-while-the-servos-cycle-through-a-sequence-reminiscent-in-sound-to-the-G
Read more…Does anyone happen to have a diagram showing (or know) the position of the three mount holes in the ArduPilot Mega - i'm looking to have a mount plate cut for my arducopter project and would rather have accurate reference for the PCB mount holes…
Read more…Hello everybody
Im new here and im making as a hobby a tricopter. I have a few questions.
I want make a system that stabilize the tricopter. But how does it Work? Is ther a generalsolution for ? I know that you have to use a gyroscoop and a accelerati
Read more…When I go into arduino IDE preferences, I tick the box that says "automatically associate .pde files with arduino", but then after I exit IDE and open IDE back up again, I go into preferences, and the box is un ticked again. And I've tried right clic
Read more…Hi, I have been setting up the APM+oilpan with MediaTek GPS with the public Beta. I am not geting a GPS lock signal displayed from the ABC led's. But it will get a GPS lock with lat. and long. displayed in the CLI when testing via USB in dump mode.
Read more…So I think I got it all up and going now how does this look? Only tweeked a few numbers... Is the Z accel number right? I take it when I give it thrust this will be at zero?
Hi all,
hii
some one can help me please
the blue led in the imu v2 with the gps EM406 is not locked , why?
Read more…