*RULES
Hey Here,
We are sincerely looking for the regional agents worldwide. The agents should qualified for the following requirement:
1. We have the simiar market and it would be great if you had some potential customers in our LiDARs' main application:
Ben
The ARCHER GR8 FrSky receiver features the new ACCESS protocol. ACCESS provides the lower latency and increased performance of our previous G-RX8 receivers. With OTA (Over-The-Air) function support firmware upgrades will be very easy, no more wires.
Read more…I am close to the fun bit of my new build but am dismayed that I cannot find any folding propeller to fit the design at 1855. The thought of bolting props onto the beast every time I need to launch does not excite me.
I have read some bad things about
Read more…Hello, I hope someone can help.
I have a X6 hex, with a Tarot gimbal running firmware 1.5.
Sometimes I get pitch wobble in the video, which is not apparent on the hex. I have even had it after landing when the hex is completely still, so definitely a g
Read more…This is a new problem for me but I am sure the answer lies in the physics of batteries and that one of you can explain it to me.
I have a new X6 build using Pixhawk I have Taranis telemetry working. I have had a few test flights to see how things were
Read more…Hi,
During my first experimental flight with:
Tarot X6 960 frame
2x Tattu 10A 6S LiPos
Taranis X9D+ with S3 switch installed
FrSKY X8R
3DR original Pixhawk with Arducopter 3.3
I had an issue switching flight modes (switch setup on S3 multi-position): flying
Read more…Well, I should have taken the advice of, pretty much everybody, and built a simpler model as my first build. But I didn't... I jumped right in and built a DYS D800 X8, and a Tarot X6 at the same time. I took the D800 X8 out yesterday for her maiden f
Read more…Hi all,
I'm assembling a Tarot X6 with some electronics (LED lights controller, LiDAR, Connex etc.) and I would make the work as clean as possible.
In order to safeguard the parts, I would mount the GPS antenna on the very top of the central chassis (u
Read more…Hope one of you guys can help me identify a root cause to this accident here:
I have just finished a large hexacopter build (Tarot X6, 18" props, 325Kv motors), and on it's second flight, shortly after takeoff, it slowly started yawing left, feeling f
Read more…I know this topic is recurrent but I can't find any relevant discussions to guide me in my quest to resolve this.
Background:
I have a new X6 Tarot build. It's flying very well and I finally got the confidence to lift my sony A7II on an home made RCtim
Read more…Hi all,
I finished my Tarot X6 960 frame that I will use for experimental purposes.
I need to open the upper plate to shorten some cables and I found that almost all of the M3 screws that go into the spacer are stripped because I used too much thread l
Read more…I have been troubleshooting my Tarot X6 960mm hex running Pixhawk, and cannot figure out why it is flipping on takeoff. I have reviewed a number of other forum topics, but can't seem to get a stable takeoff. Recent corrections/checks have included...
Read more…Hi guys,
I have a strange problem with the motors on my Tarot X6 960 that I am setting up.
Details: Pixhawk Arducopter FW 3.3.3, Taranis X9D+ radio, X8R receiver, setup made with APM Planner on Mac. Question about CH.1 to CH.4 behaviour.
Radio calibrate
Read more…All of the Archer receivers are hyper-matched with the ACCESS protocol. They not only feature wireless firmware upgrades, increased range, and telemetry performance, the R4 now supports more functions like configurable telemetry power, S.Port/F.Port
Read more…FrSky Xact series coreless servos utilize all CNC machined aluminum protective case and metal gears, these servos are 8.4V high voltage capable and offer high speed and configurable torque performance. Also, the Xact series servos offer multiple form
Read more…Time: Thurs, September 20th - 8 am MDT.
Phase One Industrial together with Air Supply, a UAV Partner, will show you how integration with a Gremsy gimbal can keep you ahead with the latest technology.
In this webinar you’ll experience:
More in-depth crit
FrSky Receiver TFR4SB is Compatible with FASST 2.4G: Air Systems (7CH Mode/Multi Mode) & Surface Systems (C1 Mode) Finally an affordable S.Bus reciever. Not only is it affordable, but we offer improved sensitivity and stbility for better comunication
Read more…As a portable radio, the FrSky Transmitter X9 Lite is a remarkable fusion of traditional radio design with the innovations of the latest ACCESS protocol. The X9 Lite inherits its classic form factor from the FrSky Taranis X9D series remote control, a
Read more…The DJT telemetry transmitter module is a great choice if your transmiter is compatable with the JR modules. (as well as Turnigy 9x/FlySky 9x/EMAX 9x)
The Telemetry Radio System developed by FrSky provides an additional return link that is used for mo
Read more…