Hi all, My setup is as follows: Pixhawk running Arduplane 3.2, RFD 900, Futaba s3005 servos on all surfaces including throttle, Gasoline engine. I have been using pixhawk along with an electric powered plane without servo issues.In the above configur
Read more…I'm using an APM2.6 board, and a 3DR voltage/current sensor board. I had to adjust the voltage multiplier upwards in order to get the voltage readings correct
BUT...
If a 4-cell LiPO has measured internal resistances of 4,4,7,6 milliohms (respective
Read more…I have a Iris+ with the Iris+ FS-TH9X controller.
I found one of my switches was broken today. Does anyone know where I can buy a replacement switch?
If your looking at the controller it is Top Left Rear switch. It is a spring loaded switch and not a t
Read more…Hello Everyone,
It is my hope to meet someone from my state of Kansas
That would be willing to mentor me a little. I have
APM 2.5
Thanks Everyone,
Darrell
Read more…hola soy nuevo aqui Estudio Agronomia Y Necesito contactar Con Alguien Que PUEDE MODIFICAR EL aplicación TORRE ESTO CON EL FIN DE agregar nuevos modos de vuelo espero de su ayuda saludos
Read more…In Aviation E Brief today it is reported that The FAA have received more than 325,000 UAV registrations making more drones than piloted aircraft at 320,000 in the USA!
2 points from this.
1) Time for a rename of FAA to FDA Federal Drone Agency? or I w
Read more…
This is a discussion to focus the feedback and support of ardupilot on the PixRacer board from AUAV.co.
We believe that all teething problems encountered are now resolved and so we recommend people load Copter-3.3.4 which is available for all multicop
Read more…Hi all,
In Mission Planner (1.3.34) > FlightPlan > right click >Map Tools > KML overly.
I have a KML which calls a PNG to be overlaid.
Problem is that for some reason the PNG does not show up.
Can anyone tell me the KML sysntax needed for this?
right n
Read more…Hi all, I've had my multi's and plane set up with 3dr radio telemetry & OSD etc, I just want the ground station functionality in the field but have a portability issue with computer And I've been patiently waiting for the iOS release for mission plan
Read more…no reply in the mini APM Pro forum so, Powering the Mini APM Pro.Hi everyone,I've had two of the mini APM pro's and the standard mini APM for a while now one has Had a crash . Since reinstalling and setting up on a hex f550 I've found a power issue.
Read more…Hello,
I'm having a battle with my compasses. I use pixhawk clone and M8N GPS with compass.
I'm unable to find orientation setting, where I will not have EKF compass variance errors.
I think that this is not mag interference problem because this happens
Read more…Hey fellas,
I have had an interesting situation. My pixhawk hex has been flying beautifully with the turnigy 9x radio with the 9xtreme board. I've upgraded to the Taranis x9D plus, to unlock 16 channels.
First test flight today, and things go cra
> I've had my multi's and plane set up with 3dr radio telemetry & OSD etc, I just want the ground station functionality in the field but have a portability issue with computer And I've been patiently waiting for the iOS release for mission planning.I
Read more…Hi all:
Some of the Folks from the FaceBook 3DR and Mapping Groups said I should post my website on here so Here goes:
The Message Title pretty much explains things. Please check out my Web Site. you can check with the Facebook folks for References.
Read more…so my quad lost control in loiter. I was flying it for the 5th time just hovring around, flipped it into loiter and it started pitching forward. So much so i went back to atti and brought it to the ground. The mission planner started screaming "er
Read more…Hi,
tried to connect the uBlox neo 6m-0-001 with compass to APM 3.1 mini to the GPS slot (compass to SCL/SDA, GPS to GND/5V/RX/TX).
The power LED on the GPS board in on, compass configured and works fine.
I cannot get the GPS working, getting interchan
Read more…hello everyone, i dont have any gps yet, want to get some suggestion before i buy one of it.
which is better between ublox neo-m8n and ublox neo-7m?
or any suggestion for other gps maybe?
im noob with it, for sure, haha, this is my spec
f450 frame
Lipo 2
I have a Jr with a 140 degree plate. Does that mean in MP I configure the servos to be 40, -40 and 180?
Read more…I am using v3.3 rc1 and I have no way of getting the collective pitch to go in the right direction as well as making the stick on my transmitter (Futaba) go the right direction without messing up the servo directions for the accelerometer outputs. So
Read more…APM Planner v2.0.18 installs fine, then crashes when run on a current Win8 machine.
Here's the Dr. Ming output:
apmplanner2.exe caused an Unknown [0xC000041D] Exception at location 036B5171 in module Qt5Quick.dll.
Registers:
eax=00000000 ebx=0cb198f8 ec
