Hi,
I'm trying to add a servo gimbal to the Pixhaw. What ports do you connect the servo gimbal to? On the mission planner, what translate to the RC9 - RC12 ports that it lets you choose from?
Thanks
Read more…Is there any way to "force" it by entering it manually, with a checkmark for "always", making sure no external factor would reset it, like a battery disconnection ?
That would allow for some specific missions to double-up the distance range.
Read more…I'm sure this question will be answered eventually in the wiki, but say someone wants to use the older style 3dr radios. What is the pinout of the pixhawk telemetry plug? The other end of the pigtail will be cut and soldered directly on the radio.
negative headlines why?
For some time I have been following the report not only here in German forums. there is to read ticking time bombs, Russian roulette, board dead after 6 flights
APM in the new version is at eye level with the big FC as DJI, Mik
Hi guys, not sure if I'm the only guy to notice this...I used to be the only weird one at my model club who was APM-ing, with full telemetry etc etc...Now I have got a few more guys into it,, I had my model out on the field, with my Telem computer ru
Read more…Is it possible to operate an APM copter from a boat?
As far as I understand, the gyros need to be stationary when they initialize?
Is there a way to work around this, so that I can take a copter out to sea on a boat which may be rocking around, power
Read more…Hello drone enthusiast.
I`m from Austria so please don`t mind my grammar or spelling.
I have a big problem with my APM2.6. after canceling the wizard because i forgot to configure my remote control. I can still update the firmware but then can`t connec
Read more…I have been flying with a Bilxer 1.1 and APM 2.5 for several months with few problems. I upgraded the motor/ESC and then balanced and recalibrated the accelerometer. Now when sitting still on the ground the plane is reporting that is it bouncing, t
Read more…So I have a wire going from APM UART0 Tx to Rx on an Arduino and I monitor the Arduino serial output via USB back to my computer. I have the following code to try and receive the sensor data that the APM is creating. It's a heartbeat, but I'd like to
Read more…Hi
I have searched through the discussions in this forum and Googled for this question but could not find the answer.
I am planning to mount this motor ...
http://hobbyking.com/hobbyking/store/__36765__Turnigy_Multistar_3525_650Kv_14Pole_Multi_Rotor_Out
Read more…I am trying to get my DJI NAZA-LITE to arm here is what i have:
Turnigy 9x w/Er9x Firmware
DJI 550 Flamewheel
DJI NAZA Lite w/ Gps
3D Robotics 880Kv Motors
3D Robotics ESC soldered to get motor wires shorter
In the naza assistant everything checks out and
Read more…All 3 crashes the same thing happened. took off in stable went to about 40 elevation switched to loiter, then flew about 150 yds into a 10mph wind. The best I can tell it appears that t
Read more…Edit: Unfortunately I never discovered the answer to my question. Pretty much stalled out after that.
I've started here (http://qgroundcontrol.org/dev/mavlink_arduino_integration_tutorial) and have read around the forums and had a few additional quest
Read more…The ardupilot site (ardupilot.com) lists both "Mission Planner" and "APM Planner 2.0" with no explanation as to which one to use or how they differ. What are these different options, and where is that documented?
Read more…Hi
I am trying to set up the failsafe in adrucopter .
I am using a APM2.5 running 3.1 software .
My radio is a 9XR with opentx software and an Open LRS module.
I have gone through the instructions and try as I might I cant get it to work .When I turn o
Read more…Hi everybody,
i wonder if someone can help me.
do i need a extra charger to charge a LifeFo4 Battr.?
I have already a Lipo/Charger,any idea if i could use it.?
Tks for yr help.
Brgds Helmut
Read more…I am planning on getting a new computer and need to know is the Mission Planner will run on windows 8. Also anyone with windows 8 have you had any problems with any other APM software?
.
Read more…Hello folks,
My brother and I live about 10 km from each other. We want to send the plane back and forth to each other, like a messenging pigeon. No FPV, just by mission.
I know now that there cannot be 2 missions programmed on the APM. But... there
Hi,
As I did not succeed to view the acc axis vibration levels in the log browser I've viewed the data in real-time when I was not flying with usb connection.
the x-axis and y-axis was +-8 when the quad was not moving
but what surprise me most was the
Read more…
