I am having problem with upload command from flight data. Eg Change altitude, restart mission ect. I do not have this type of problem with the previous Mission Planner. When I try to change altitude, a fail massage window appear. I also can not write
Read more…The site has changed a lot!
What happened to all the documentation for the mechanical set up for the 2x ardupilot?
Read more…Hi all,
Have starting my journey into FPV, and so far, am enjoying it! Learning quite a few new things and the risks, but on the whole, it's bloody cool! Even managed a landing! Nothing too ambitious at the moment, just getting an idea of range etc. R
Read more…Starting putting together the new 3DR Y6 kit, and all is going well. I am at the point of trying to get all the ESCs, wires, PDB and PM wires placed. Lots of wires. 3DR has some Y6 photos and all I can see is two ESCs attached with zip ties to the
Read more…Hi,
i am posting this topic into autopilot category because no one answered the post into "wireless communication" cat. looks like wireless communication is not important topic here. anyway, plz guide me on this one, as this is very important for me.
Read more…So this is very weird - I'm able to reproduce this every time.. I wonder if anyone has experienced this, or, if anyone can reproduce this on their quad or Y6.
When I switch to loiter, if I use my roll/pitch the copter will move properly. As soon as I
Read more…The first time I fly, position holding is perfect in all axes.
Subsequently (after I put it to another mode and return it to loiter [?]), the altitude does not hold. When the stick is centered, it either slowly rises (if it was climbing previously) o
Read more…I tried playing back a .tlog airplane flight that I recorded with V1.2.66 and found that some parameters said 0 or unknown. Went back to V1.2.66 now everything works perfectly. Is there a bug in 68 or did I do something wrong?
I think that I am going
Read more…Hello,
I have a problem with my APM2 with the calibration of accelerometers use the M.P. 1.2.67, and when I do the calibration, as wiki procedures, it gives me the following error "Calibration Failed", I run both in MP mode in the CLI.
What might be th
I was wondering if anyone had any success uploading the newest helicopter SW. I believe V3.0.1 according to the MP. It appears that in any mode I put the helicopter in it will not send the signals to the servos other than holding their trim value. Th
Read more…Hey Guys
I would like to properly document the individual PID settings on the latest code, with a "plain English" explanation of what each parameter does. Partly for my own education (To be able to support the ones I sell), and to perhaps make a WIKI
Read more…Andrew has told me that the tlog format is very simple - an 8 byte microsecond timestamp followed by the raw MAVLink packet.
I have parsed Mavlink packets from tlog file, but I can't get timestamp. What is the varible type for this timestamp? uint64_
Hi Guys
Been going through testing the latest batch of APM 2.6's I received.
I have a problem on one of them, and want to see if I missed anything before requesting RMA.
We have the APM connected to the GPS/Mag ONLY. No other connections, input or outpu
Read more…I have a dji f450 and am have been looking for a case for transportation, but have not been able to find one to fit it. Does anyone have any ideas for a transportation case?
Thanks!
Read more…I am having a problem with APM Plane. Here is the background info.
Hardware:
Turnegy 9x
Finwig plane with electronics from Finwig (Built plane first and everything works)
APM 2.5 with power module (latest firmware)
fully charged battery
Situation:
I put e
Read more…Can anyone tell me what is the orange line on the Mission Planner means ?
On the Flight Data screen, it says the orange line is "Direct to current WP".
But all my WPs are set on one part of the map and the orange line is point away from these WPs clust
Read more…Hi guys,
I've been testing the airframe post compassmot and it's flying well - managed quite well in loiter in a moderately windy day here. Definitely twitchy, but held it's position well - and after a one hour warm up on USB, the baro was holding it'
Read more…Hi,
I'm planning to build a hexacopter and trying to find some motors which will provide good efficiency. The up in air weight will be around 3.6 kg(600-900g frame, 6x150g for motor + esc, 800g battery, 500g gimbal, 500g camera) give or take a few hun
Read more…I have a large H frame quad and noticed the new "H Frame" option in MP. I had always run my quad as an "X" frame, which works just fine. I posted a query asking if there were any special features that came with this choice and was told, no, it's jus
Read more…I need some help with altitude hold. When ever i switch to it, it levels for a second and then goes up. Same with loiter. Any ideas?
Read more…