Hi,
I am looking for the Eagle files of the Version 2 PPM encoder. The ones posted on the product page seem to be an older version without the oscillator. Any chance of getting hold of the updated files?
Read more…I've got a flat area that is 10 meters wide by 15 meters long. With just a GPS and no magneto or airspeed sensor, is it capable of landing in that size of an area? I would set the previous WP directly in line so that it has a straight approach.
Would
Read more…Does any1 have an idea on how to setup the arducopter to indicate via different color leds on the motor mounts as to what mode the copter is in, eg. stabilize, alt hold, loiter.
From what i can see in the code (APM_Config.h)
There are these lines:
#defi
My friend and I have been working on setting up the latest APM in an elevon configuration, and we have tried everything we see in troubleshooting guide. Basically, we can get the rc control and the sticks in "stabilize mode" to work correctly, but th
Read more…I have been messing around with this, but unless i connect a my radio to the APM board it will never send any readings to Xplane?Does anyone know if this is possible?
Read more…The wiki says that in beta1 the delay and minimum alt for a waypoint is disabled. Is it still beta1?
I successfully made a mission with 2 waypoints and a land command at the end but it looked like it started to descend too fast. Almost looked like a n
Read more…Any1 thats new to quad rotors has no doubt discovered the infamous 1st flight wobble/flip copter effect caused by quite a few things done or not done.
I found a great way of testing the copter before actually allowing it access to wide open spaces an
Read more…Hi Michael
I've been intrigued with the UDP connection option in the APM Planner. I can't find much documentation on this. Here's hoping it's an experimental option to connect to the APM over 3G Internet!
Read more…Has anyone ever experienced a motor not being able to spin up? It just sort of jitters back and forth like its trying to start, but wont spin up. The weird thing is that if I disconnect and reconnect power, the problem goes away. It is only about 1 i
Read more…
HI All,
A couple of us here in Brisbane, Australia have been trying to get our ArduPilotMega to fly our "test" aircraft, in preparation for implanting the elctronics into something bigger for UAV and/or FPV.
Our problem at present manifests itself i
Read more…I think my (official) XBee needs unbricking. The green light does not come on, so I'm going to take the steps described in the manual, but I just need some confirmation before I completely wreck my h/w:
I'm having an issue with one of my APM boards.When I connect power to the servo rail, the red pwr light and the yellow mux light both turn on, but the blue PPM light stays off. When I plug in a USB cable, the blue PPM light comes on, but the other tw
Read more…Hey guys!
My copter wants to roll to the right when I am in auto-trim calibration mode (arm for 45s)
My TX trims are centred, and Iv calibrated it on a level surface. It flies alright in stabilize mode,
but lists to the right, thats why Im trying to ca
Read more…I've downloaded and AMP Planner 1.0.55, but I still have zero for my mix values? The GPS altitude is correct, but the mix is zero all the way through?
Extract:
Read more…GPS: 33120500, 1, 10, -33.8417400, 18.5144820, 0.0000, 125.1400, 117.2200, 11.0700, 9.8400
A
During a test fight I noted that the modes I had programmed in setup did not seem to operating correctly.
I have APM 2.22 installed in control board.
I had " Manual, Stability and RTL " set in the 3 position mode switch. the first 2 modes seemed to wo
Read more…I just flew my maiden flight with my new, totally custom octocopter. Everything worked really well except that I entered into a heavy oscillation, which I was able to recover from. Does anyone have any advice for PIDs for such a frame? My frame is al
Read more…Hi,Any one tried to install ardupilot mega in T580. I opened T580 it has one speed controller which controls all 4 motors and it has i suppose 2 differential inputs coming from its controller board can APM handle this or have to put 4 speed controlle
Read more…Iv attached a video of the problem.
I booted the copter up on a flat surface, then transfered it to my prop saver string.
In case you think it is the fact that Its hanging, its not. Same thing happens on the ground....
Its most likely a stupid error,
Read more…Hi,I am wondering if mission planer could use scan map as internet is not available at all the places or there is any way to use goggle earth without live net?Ahmed
Read more…I have found that using HK GCS lite the mavlink serial data seems consistent over reasonable range with no errors using Xbees on 2.4GHz and 57600 link.When I use the Planner under the same conditions I can see in the background window various message
Read more…