GPS: 770000, 1, 10, 41.0994610, -92.4471590, 0.0000, 711.8800, 702.9700, 19.9400, 195.1000
How do I convert the timestamp? Is altitude in meters? Is that the 711 or 702?
19.9400: This speed? In mph?
195.1000: Heading?
Read more…
Right now a polygon point in the planner can not be moved once it has been added. Is it possible to make them editable, i.e. can be dragged like the waypoints?
Another suggestion, when right click a waypoint/polygon point, it will be nice if a "delet
Read more…Hi guys
I have a fully assembled mini-arducopter. I want to use Cmucam on my arducopter to implement line-follower. My concern is if the cmu cam can actually detect the line underneath when my arducopter hovers in the air. Because i can't seem to fin
Read more…I tried a mission again and it looked like it was following point1 and 2 but after that it was just drifting away. I was wondering, what happens if a mission takes the arducopter out of range, will it abort and just go its own way? Atleast it did not
Read more…I have experienced a delay when switching from Alt_Hold to Stabilize and this caused a little crash. The funny thing is that it 'feels' like the same type of lag when the rudder commands become unresponsive.
I have logged an issue here: http://code.go
Read more…Hey guys
going a bit back in time im trying to get my ArduStation working with current APM code , if you look at the useit section of the ArduStation then they say fr Ublox GPS use 57600 baud for a EM406 use 38400 but now if your APM telemetry is run
Read more…I updated Mission Planner to 1.0.59 hoping to upload Arducopter 2.0.39b, but no success.
a banner pops up: 'Can't detect your APM firmware version. Please check your cabling'
I erased the EEPROM and reset the factory defaults. Mavlink seems to work f
Read more…Can I use my spare APM with mo additional hardware for X-plane simulations? Or do I need to connect the oilpan and a receiver?Magnus
Read more…I can no longer set modes on the flight data page ove xBee.
I can do it when connected to USB but not over xBee.
I tried reloading the firmware and just upgraded to the latest planner.
I initially thought that it was simply a hardware issue and that I w
Hi Everyone,
I m searching for best IMU unit for contructing my own autopilot system, with following features:
Hi everyone,
I was checking my APM on my plane and I've instaled the last version of the software from the APM Mission Planner. After 1hr of take my AP at completely out of my house, with no anything between the GPS and the sky, I can't get the GPS fi
Hi,
I am looking for the Eagle files of the Version 2 PPM encoder. The ones posted on the product page seem to be an older version without the oscillator. Any chance of getting hold of the updated files?
Read more…I've got a flat area that is 10 meters wide by 15 meters long. With just a GPS and no magneto or airspeed sensor, is it capable of landing in that size of an area? I would set the previous WP directly in line so that it has a straight approach.
Would
Read more…Does any1 have an idea on how to setup the arducopter to indicate via different color leds on the motor mounts as to what mode the copter is in, eg. stabilize, alt hold, loiter.
From what i can see in the code (APM_Config.h)
There are these lines:
#defi
My friend and I have been working on setting up the latest APM in an elevon configuration, and we have tried everything we see in troubleshooting guide. Basically, we can get the rc control and the sticks in "stabilize mode" to work correctly, but th
Read more…I have been messing around with this, but unless i connect a my radio to the APM board it will never send any readings to Xplane?Does anyone know if this is possible?
Read more…The wiki says that in beta1 the delay and minimum alt for a waypoint is disabled. Is it still beta1?
I successfully made a mission with 2 waypoints and a land command at the end but it looked like it started to descend too fast. Almost looked like a n
Read more…Any1 thats new to quad rotors has no doubt discovered the infamous 1st flight wobble/flip copter effect caused by quite a few things done or not done.
I found a great way of testing the copter before actually allowing it access to wide open spaces an
Read more…Hi Michael
I've been intrigued with the UDP connection option in the APM Planner. I can't find much documentation on this. Here's hoping it's an experimental option to connect to the APM over 3G Internet!
Read more…