Hello,
I have got my ardupilot up and running, everything is working fine with all components (shield,IMU, and ublox GPS) now i tried to connect the servos through the board. However, they are not responding to inputs given by the controller. i kno
Read more…Hello everybody
I am a newbie regarding UAV´s and I just nearly purchased uav/fpv equipments from FPVflying.com. I dont want to start a war or something like that, but I sereasly dont like to pay huge amount of money and get such a bad service from th
Hi all. I have just received my fully assembled Arducopter (http://store.jdrones.com/product_p/acq11arf.htm).
I also own an Eurgle 2.4Ghz 9x TX from r2hobbies.com.
I'm new to RC and I don't even know how to connect the Receiver to Arducopter. I under
Read more…I would like to build a foamy UAV. Using the ArduPiolot and a scratch built airframe. I have a few designs that are very stable that fly just as well at 1/4 throttle as they do at full throttle. My big question that I haven't been able to find on the
Read more…I use the ardupirates NG code,
i have enabled camera stabilization in configurator and DIP switch
connected 2 servos, it works,
but according to this http://code.google.com/p/ardupirates/wiki/CLI
i should have "f" and "g" commands in the CLI to calibrat
Read more…I've got a strange issue with ardupirates NG,
when i first connect the battery today to the arducopter,
then trying to takeoff it pulls to a direction very strong, like if the front and left motors are running stronger without touching the stick !
i di
Read more…im making a bicopter and thought of using the kkmulticopter board. does anyone have a diagram of where to connect everything? thanks
if you dont know, will this set up work? ive attached an image
Read more…http://img268.imageshack.us/i/avatar1yj.jpg/what is it caled? im making a bicopter and need sturdy joints which i wanted to directly bolt to the servos, i just dont know the name of the joint.thanks
Read more…As always thanks for the APM and GCS programs!
I understand APM 2.xxx software is Beta.
Just making sure I'm not making an obvious mistake.
Also posted in APM ISSUES section.
Just wondering if anyone else is having lockup issues with the latest versio
Read more…Hi All,
I just joined the community. LAst weekend i spend building my Quad. Got the esc's calibrated and went on to connect my APM + oilpan.
I've been trying to connect to the thing on 3 computers now but without success.
What have i done so far.:
MACboo
So, the weather finally cooperated for the first time in a long time so I took my small delta wing out to see what I needed to do to get it ready to fly in Auto mode.
In manual mode, everything was fine as expected. It's been a while since I last flew
Read more…Hi everyone,
does anyone tried to use this audiomodem (based on an attiny2313) ?
http://www.aeromodelismovirtual.com/showthread.php?t=7188
Is it possible to use it with the ardustation instead of the Xbees ? (without a lot of mod)
thanks
Cedric
Read more…So i just purchased a Futaba FP-T8UAF. How can I reset this thing back to factory settings? Or at erase the saved settings per model. I am getting the hang of changing settings from the manual but it would be nice if I could start fresh with factory
Read more…Hello,I'm trying to make the RQ-1 Predator B UAV model built by NitroPlanes into a UAV. I purchased the ArduPilot Mega but I have a question on the receiver I should purchase. I will be using 5 servos on the airplane (2 for the v-tail, 2 for the aile
Read more…right, im basically making a bicopter in the form or 1 of thesehttp://www.simshack.net/images/sa-2-samson-avatar-fsx-1.jpgbased on this system because its the only one i could find based on a bicopter that i dont need any specialist eqiupment for, it
Read more…Hi,Can anyone tell me approx current consumption of an APM, Oilpan and GPS ready to go?I cant seem to find this figure anywhere.ThanksD
Read more…I setup ArduCopter today, and everything was fine. I was playing with calibration, and at some poin output 4 stopped working. I hooked up my scope, and I see the PWM signals on outputs 1, 2, and 3 - but nothing on 4. I traced back to the multiplex
Read more…Hello to everyone,
This is my first post on this forum and I would like to share some data that I determined experimentally. The test was originally set up to determine if two overlapping rotor disks performed any differently than two non-overlappin
Read more…APM Mission Planner 0.4.20
Thanks for the Planner!
I downloaded and installed the latest APM firmware via the planner, worked great!
All sensors mentioned are the ones suggested in the APM manual and purchased from DIY Drones.
I have airspeed, UBLOX,
Read more…Hi
I have trouble with my x-y Gyro readings. I’ve got the new APM with an IMU Shield bought at buildyourowndrone. When I connect it to hk gcs the x-y gyro readings drift away. Sometimes it is drifting slowly and is reacting to movements; sometimes i
Read more…
