Hi I am using the latest APM planner to update the firmware on my APM.
When I connect the APM board and open the GCS console in the APM planner, I can see the response of the instruments and everything seems OK.
When I try to connect the APM via Happyk
Read more…
Is there one place all the defines are listed with options, or is reading through the multiple config files the best way?
Is there a discussion thread for the libraries? I'm mostly interested in when they're going to be changed.
Thanks
Read more…Hi all,
I wonder if some of you might be able to help. I've just finished building my quad using the arducopter kit. I've taken my time building as I want it to be right, and made sure to read every bit of the wiki. Loaded the most recent Ardupirates
Read more…Hi All,Since updating to the latest code i cant seem to get airspeed to show up in the MAVLINK GCS in the Planner, when using Xbee...
If i go to CLI, and test the airspeed sensor, it works.
If i power the APM with usb, Airspeed works over XBEE in Plan
Read more…Good day for all!
I want to make an UAV, which cans fly using webcamera to determine his way.
There are fine libraries to analyse images, such as OpenCV.
But i need to have operating system(maybe linux) and powerfull processor (as x86 or ARM-9 etc) to
Read more…Hello!
I'm trying to install Labview drivers on my Laptop to setup PID values (with Configurator) outside but with no success. It always says that it can't locate 2009 SP1 Runtime Labview drivers ...
I did it on my home PC and I had no problem ...
Is th
Read more…First of all thanks for this super software.
Doug I followed your changes for battery monitoring.
I have set the battery to 4, using the atto current sensor.
How can I access U,I and most important battery_remaining in the GCS (Planner or HKGCS)?
Thank
im basically building the vehicle in my profile pic and i need to know if it will lift or better yet, aerobatic (in a sense)i got the motor with the closest specs the props required.props: 10x4.5motor:outrunnerC3542 KV1000 (on ebay, its £10, p+p=£10
Read more…Dear All, Hi, we have an APM 1x board with the 1.02 code and the throttle is not working even if THROTTLE_OUT and THROTTLE_IN are set to one. We have also tried updating to the latest version of the firmware, on the repo but the stabilization doesn't
Read more…Hi All,
I`m having problems to upload the code to my new 2560 board.
Program: Arducopter Mega
Arduino 022
Board: Diydrones Mega 2560
Operating system: tried in Windows XP and MacOSX
When I try to upload the code the yellow leds in the board start blinkin
Read more…Hello, today I uploaded my quadrotor code to the custom controller board to start testing its stabilization. I've been trying to tune it all day but I cant seem to make any progress... I put the copter on a test stand to hold two opposite sides and t
Read more…im actually preparing for graduation project,
and i m determined to make rc helicopter with no autopilot, no UAV, no senser, but receiver and transmitter,,, so that i can control only power and direction,,,
plz, help me, what component i need?
which
Read more…i was wondering if their is a way of using the two pot trims on the remote for mode selecting?
Read more…I know it's been posted before but my experience may outsider a few more newbs to take note.I am referring to a brand new HK450GT Pro from Hobby King's retail store in Sydney. Added electronics and spooled it up in the lounge to check for vibrations,
Read more…i have done the transmitter calibration with the configurator,
all seems ok and it gets the right values and positions,
i hit save,
but then when i disconnect and reconnect the copter to USB, the "transmitter" screen in the configurator screen shows all
Read more…Could someone help with a tip? After several hours of trying to work and searching for a solution on the Internet, I am about out of options on why flashing the firmware in my brand new Turnigy 9X won’t work. I tried several guides posted on er9X htt
Read more…Anyone found a hyperspectral, or atleast extended spectrum camera that can visualize in complete darkness?
Basically a night vision camera without the need of adding ir light itself. For sensitive enough cameras even dark nights should be possible to
Read more…If you only allow the GPS coords to be assigned to long, lat variables in GPS hold mode only one time when the switch is flipped, it could be used as a Return To Home command, couldn't it?
I think this is the associated code:
----
if (gps.fix){ // We
Read more…hello,can anyone help me to use kalman filter with 3 gyro and 3 accelerometers?anyone have a code in c ?thanks.
Read more…hello,
can anyone help me to use kalman filter with 3 gyro and 3 accelerometers?
anyone have a code in c ?
thanks.
Read more…