Short story ( If you wanna skip, go ahead, it's not purely relevant lol ) :
It's my 18th birthday this 18th Feb so I dared to talk about this project and budget with my dad... Luckily he said yes! It's not for any science fair or stuff but for self-l
Read more…I have a lot of questions as I am learning about the ArduXXXX world. Is this the best place to ask them or the forums over on the ArduPilot site?
Here are just a few of my questions:
Hello,
I have started to build a drone, I am using the FS82 PPM receiver and the FS-i6s transmitter but am facing problem while binding the RX and TX.
Can any one please guide me on this???
Thanks & Regards,
Prathamesh P. Badhan
Read more…I am building a drone from scratch. Presently I have the frame all together. I am in the process of of wiring it now. I received my Evolution Digital Radio Control system. It came with the TGY-iA6C Receiver. This is where I got stumped. I'm not sure
Read more…Hey folks,
I've scratch built an RC plane and ground station (hardware, software, and frame all scratch built - not using Ardupilot nor a pixhawk) and want to develop an autopilot for it.
I'm familiar with control systems and I'm considering using a so
Read more…Hi new to drones and I am designing a flying wing and doing modifications to a fixed wing drone. I made a design in XFLR5 for the flying wing, after analysis I am getting a CL value of 0.119 at zero angle of attack at a speed of 15m/s. Is this a typi
Read more…Hello friends i got a college project to make a quadcopter that can fly upto 500m range and can lift 1kg payload simultaneously .
Can u guys help me and suggest me the motors and the parts needed to make it plzz ??
Read more…Good morning everyone.
I had a problem at the GPS during a flight near my home, I passed under high voltage cables and bumped a cable with the wing of my Bix3.
Right after my Frsky X7 started playing for low RSSI.
The APM went first in Failsafe Short (C
I am trying to use an Arduino Mega 2560 + GPS module + IMU module on a rover (because I had all this stuff and I don't have a Pixhawk setting around). I followed the instruction, downloading the latest Ardupilot software ant the special Arduino IDE,
Read more…sombody please advice me some useful tips about swarming of drones...i am a layman to this field...i want to lift an object using 3 drones which can coordinate with each other...!!!
your help will be greatly appreciated ty :)
I want to control Multiple UAVs with Qgroundcontrol (similar to this simulation) over wifi. For single drone control, I can connect my pc to the wifi of a drone but I can't change to select other UAVs in Qgroundcontrol as shown in that simulation. I
Read more…CE30-D is a complete solid-state LiDAR with large measuring range and high resolution. It can be used in UAV such as drones, cars, robots and so on to detect the range, altitude holding, obstacle avoidance, self-guiding and so on
Feature: Complete
Read more…Dear DIY Drones,
I have got a new DSC-WX350 camera for been used in a fixed wing plane for precision agriculture analysis and I don't know how to trigger it from pixhawk. Can somebody help me to make a connector cable to trigger the camera from pix
Read more…So I have not flown in a long time and I just replaced motors/props and ESC's I am trying to recalibrate everything and update it all and get flying again.
When I go to initial setup in APM it does not recognize and I can't update firmware.. I am u
Read more…Hi all,
I am sure this question has been already asked but I couldn't find it on the forum.
Do you know how to access and/or why all the dev.px4 pages are down?
Thanks in advance
Read more…Icevo company is developing the DroneRoute platform, for the Internet of Drones. This allows visualization of all the flying drones on the map and interacting with own drones. The communication is using the new IoT mobile standards LTE Cat M1/NB1. Th
Read more…Hi everybody,
I've a DYS V8 D1100 octo with 2 parallel 6S batteries. On the frame, there is an integrated power module which provides several 5V and 12V outputs and a graphical voltmeter.
I would like to use Pixhawk, I can simply supply a 5V to a
Read more…Hey forum,
I'm trying to build a rover that uses dc motors with apm (2.8) and an L298p motor shield (that was for Arduino).But I found out that apm uses PWM (single) channel does not match the l298p motor shield requirements.
So I am trying to find dc
Read more…Thought this would work but so far no joy. Keep running into problems. Any advice?
Read more…i Newbie here.
I've been working with Pixhawk for a few days now. Came close to flying once or twice. Have successfully done all setup/calibrations a few times.
No trouble loading firmware. But now upon connecting by USB or telemetry I have an endless
Read more…