Good day all,
I'm a bit sad. I just lost my lovely quad, my digital camera and CL antenna...See below:
Chronology:
Yesterday afternoon my lovely quad just crash.
I make a loiter mode after a minute take off. I move slowly rudder and camera to record the
Read more…Hello all, sorry, i need your help.
Channel 4 output is a lot of lower than others ,
Input are ok...
Can you help me to correct this? please see attached files...
Regards
Cristian
Read more…Hi everyone,
I recently finished construction of my 3dr ArduCopter kit and began calibrating the electronics. I used the CLI to calibrate my radio as the GUIbased one didn't work, but other than that, everything went without a hitch. I finished calibr
Read more…Hello, all , im working with APM 2.5, in X configuration, when i arm the APM, one motor (motor 4) spin slow than others 3.
When i calibrate the ESC's in automatic mode, all spin with same speed and work fine, but when
i arm the APM and test, motor 4
Hello,
i bought the ardumega 2.5 + and the ublox gps together from 3drobotics.
The GPS will not lock onto any satellites. I am powering both right now over USB from my laptop. I am outdoors in a clear sky. I ran the CLI gps test. it says the ublox is O
Read more…Hello,
We are in the process of fine tuning a large octo and a small tricopter, both using Arducopter 2.8.1. We have challenges with the loiter and RTL mode. In one flight loiter can be perfect, and then, after flying around, the multicopters don,t wa
Read more…Hey,
I'm not really a begginer but this is my first big quad and i need some advice.
My setup is:
-Tarot fy650 frame
-hobbyking blue esc 40amp
-multistar 390kv
-4s 4ah battery
-15x4.5 wooden props
-APM 2.5
-Weights 1.8kg
Does anyone has a similiar setup that c
Read more…Hi all,
i'm an italian university student and me and a pair of friends are really interested in building our first drone (probably a quadcopter). I see that the store has everything we need but, since we are down here in italy, we are going to spend a
Read more…Just an annoying problem with the motors pulsing in Altitude Hold.I don't seem to be able to tune it out entirely. I've disabled the Sonar. The Quad holds altitude quite well but the pulsing upsets the stability a little.Also I'm using 12x8" APC prop
Read more…Hi,
I was reading the arducopter manual information about the sonar and I saw this:
"You are also advised to use shielded cable with the shield grounded at the APM side."
http://code.google.com/p/arducopter/wiki/AC2_Sonar
I am using the Maxbotix LV-EZ0 a
Read more…New to this subject in all respects.
I'm looking for some hand holding - This June (6 weeks) I'm doing a Robot Camp at my university for 12-15yo students. Much of the student time will be spent with Lego Mindstorm but I would also like to buy a gps e
Read more…Hello,
Is an H frame supported by APM/arducopter?
(there seem to be only X or + config, what applies to an H frame quad ?)
I am new to this level of UAV.
I have a Hex X 2.9.1, 800kv, 12x4.5, 5000 3S, AUW 2500g. 8+ min flight, all balanced and centered
Hovering in Stabilize mode is good, but it seems to want to pitch slightly. forward or back. I have to stick hold position
Read more…RC signal loss, hence RTL triggered. However, to my surprise, RTL has been triggered twice (see picture). Blue followed by purple. The final landing place is 80m from the initial place that I launch it. Anyone experienced this before?
Read more…Last night i used an XT 60 to Deans converter plug made by a friend to connect a battery to my quad which has an APM 2 board and I use the APM Power Module. Well i did not check the plug before i used it which was a mistake as it resulted with me co
Read more…I am looking for a list of the Standard and Advanced Parameter list that shows the default settings and helps with setup.
I am particularly interested in:
Standard List
Acro Axis Should this be enabled or disabled for a quad?
Advanced List
Yaw P Mine i
Read more…Hi you all! Now, our quad works well, but the sensors are not well calibrated. When you see the HUD, it is not straight. Here it is a photo with the problem.
Any solution to this?
Thanks a lot!
Read more…Hi you all.
I'm trying to fly my quad without using the GPS (which is been shipping). But I have some problems with it. I don't know how to save the configuration at the Mission Planner, so I don't know how to make it fly. All works ok, but I still ha
Read more…I've been jumping through some hoops to get things powered on my multi-rotor rigs lately and it occurred to me that a slightly more advanced version of the 3DR Power Module could solve it really neatly.
My suggestions for 2.0 is in addition to the pow
Read more…MHello,
I'd like to share my experience and experiments with the use of the sonar on my quad.
The config is the following:
-Quad 3DR base frame rev C
-880Kv motors, 11 x 4,7 props
-4S 4500 ma battery
-Sonar MB1260 XL-MaxSonar-EZL0 (bought in the 3DR kit)
H
Read more…