Gender
Male
About
Location
buenos aires 4
About Me:
none to say just quads fan
Please tell us a bit about your UAV interest
quads
Hometown:
san isidro argentine
Activity Feed
"Do you have old mission planner and new version both installed on same machine? im also having this problem and i think might be related to multiple apms versions installed, any hint?"
Hello allto make it short....2.8.1 worked fine in all modes 3.0.1 works much better in stabilize!!! (a world of difference) BUT LOITER OVERSHOOT!!!what can be wrong considering EXACTLY SAME components location , the same apm2 quad in fact.5010-14…
"ok answer seems to be:
In the 2012-09-30 release and in anything newer, there is a "tp_8khz.hex" build that is the same as tp.hex but runs the PWM at 8kHz. This should work fine for you if flashed instead of tp.hex. the only workaround I am aware…"
In the 2012-09-30 release and in anything newer, there is a "tp_8khz.hex" build that is the same as tp.hex but runs the PWM at 8kHz. This should work fine for you if flashed instead of tp.hex. the only workaround I am aware…"
HelloI have always used this ESC's, always very cold in temp, but now I did a simonk flash for my 4 escs ...they are getting hot after 3 mins i have to land because loss of power due to temp i think...What is the reason ? i did not calibrate them,…
"then each 4p is connected like a single cell in the balance plug, resulting in a 4s4p
would this be 100gr cables penality? "
would this be 100gr cables penality? "
"No, Im using arducopter APM2 ,so if anyone is using this control board and want to share PIDS of big motors and props, to start with, much apreciated!
LAN
regarding my conections remember that im puting each arm as parallel (4p). the resulting…"
LAN
regarding my conections remember that im puting each arm as parallel (4p). the resulting…"
"Hi LAN I do not think there will be so many cables... I'm planning a parallel 4 bats in each arm, like I (marce002) posted here:
http://www.rcgroups.com/forums/showthread.php?t=1880665&page=90
regarding the link for the 4in 1 is this: one
PLEASE…"
http://www.rcgroups.com/forums/showthread.php?t=1880665&page=90
regarding the link for the 4in 1 is this: one
PLEASE…"
HelloI' m building a 750mm arms apm2 quad with:*Rc timers 5010 and 17x5.5*Esc turnigy plush 12 from hk*4s4p panasonic 18650B inside arms (2cm alum tubes 0.5mm thick 210gr 750m2m)total weight 1.6kgcan anyone suggest good PIDS to start with to achieve…
"Please anyone tunning these big birds??
Im building an apm2 quad with:
*Rc timers 5010 and 17x5.5*Esc turnigy plush 12 from hk*4s4p 18650b inside arms (2cm alum tubes 0.5mm thick 210gr 750m2m)
IM WORRIED BY THE TUNNING pids to achieve steady flight"
Im building an apm2 quad with:
*Rc timers 5010 and 17x5.5*Esc turnigy plush 12 from hk*4s4p 18650b inside arms (2cm alum tubes 0.5mm thick 210gr 750m2m)
IM WORRIED BY THE TUNNING pids to achieve steady flight"
"I do not understand why uneve discharge might exist, in a pack 4s4p, it is exactly the same as yours lan, but distributing t in the arms...Also this lipo is an option, expensive but very light in weight.... but 3s wont be good for my 5010-14 ....…"
"and what do you think about using alum tubes 20mm diameter, 750mm lenght, put panasonic bateries x 4 into each arm?
apm2.0"
apm2.0"
"hi Lan
how did you attach the motors to the carbon rod?"
how did you attach the motors to the carbon rod?"
"when I click in the map, the URL being created contains "," instead of "." in the coordinates, this is due to regional settings in my computer i think, in order to avoid incorrect mapping, the url should be fixed maybe with a…"
Hi Is there any hint you can give me maybe in PID tunning to compensate for too much powerfull motors for a frame,motors= NTM 2826 1200kv, prop 8x47 and fram DJI flamewheelmy friend cannot hover due to climb as a rocket!! on 4000 4s, do not have 3s…
"I do 20mins with turnigy hal frame and a 5000mah 30c bat, but anyone would like to share pids for similar setup?"
"Hello!!!, I have rctimer's 433Mhz telemetry usb , it is not clear to me how can I fix the problem, I have a very bad range connecting the usb telemetry to my laptop, what can be done?"
