Hi community ,
Yesterday and today I did 2 test flight of my fresh builded SF quadcopter ( 15" carbon props and 360Kv motors)
On the first flight, all is really good, loiter is rock solid, I just want to test all function , and all was pretty good.
Toda
Read more…Hi Guys, first off,
This pertains to those with the knowledge of FAA 333 exemption Petitions using
3DR products.
I’m currently developing UAV operating manuals using;
- Finwing Penguin fixed wing
- with Pixhawk Autopilot.
I’m not sure about to wha
Read more…I did a few test flights with my phone using follow Me Mode. One problem I can't seem to get the copter to go faster than 5 meters per second in that mode. I would have thought that Loiter and or WPNAV speed would directly effect how fast follow me m
Read more…Hello Folks,
since the last update from Mission Planner to 1.3.25 I am receiving a strange feedback when trying to connect to the helicopter via Mav-Link (based on xbee 2,4 GHz).
First it is connecting like normal and most of the time after one minute
Read more…Hi All,
Hello,
I need your help guys.
I have got hexacopter with APM 2.6.
Everything was working fine with version 3.1.5. Decided to upgrade to ver 3.2.1 because of PosHold.
After upgrading motor 6 is not spinning (output 6). Motors and and every thing is ok. H
Read more…I have a 40-acre field that I would like to map every week using the same flight path. The flight last week went great and Agisoft stitched and processed all pictures with great results (around 250 pictures). Yesterday I do the exact same flight with
Read more…I loaded Plane 3.2.3 so I could try terrain following. Everything seemed fine, no errors, but no output to the ESC or servos in any mode. The mode switch works because I can see the modes change in Mission Planner.
I noticed the IO B/E Led was glowin
Read more…NXP has a development board which they call "The LPCXpresso54102 Sensor Processing/Motion Solution".
The OM13078 Development Board comes with a mezzanine board called the " Sensor Shield Board (SSB)", plus application software and sensor fusion softw
Read more…Just wanted to share this story of a quad flying with a Bee Brain,Fascinating....
Read more…my quad (APM 3.1.5) does this oscillating altitude hunting during forward auto flights....there is no such problem on AltHold or Loiter modes thou, steady as a rock.....only does this in forward flight.....anyone got any ideas or where to start looki
Read more…I used to think that either a GPS or a airspeed sensor was needed to perform centrifugal compensation for fixed wing applications. I noticed that several stabilization devices have become available on the commercial market, so I went back and revisit
Read more…Hi guys
I need some help analysing my crash or confirming my theory. APM 2.6 with Arducopter V 3.2.1 firmware.
It is (or rather was) a V-tail quad with 3printed centerplate and arms made of Balsa wood. I flied this frame for about 6 months without any
Read more…How the altitude estimation in Arduplane works with analog connected rangefinder (SF02F) on board on the altitudes covered by the rangefinder. Does the Pixhawk gets the altitude data from the rangefinder or other sourse - baro, GPS? I need to do lowl
Read more…I am currently using this airspeed indicator with APM 2.6
I have tried to use the AP_Airspeed example to read the airspeed indicator at A0 pin.
However, it gives me constant 0. It seems the indicator cannot communicate with the APM by AP_Airspeed.
I rel
Read more…Time for me to take a step back from multirotors for a little while. My loss is your gain! I'm selling my whole kit basically and I'm happy to sell it as a group or separately. Here's what we have:
TBS Discovery Pro kit: basically the gimbal frame p
FW : Arduplane 3.2.3
FC : Pixhawk 3DR genuine
I did maiden flight of skywalker x8 successfully but I found something wiered from log.
The below log shows pitch and Alt went well but DesPitch was 0 for a while. Even more the same to DesRoll too.
In second
Read more…Hello Everyone!
I have been working on this particular model for a few months now:
http://bormatec.com/index.php?option=com_content&view=article&id=78&Itemid=59&lang=de
There is a Pixhawk autopilot installed, and I have already taken it on its first mai
Read more…Hello,
So I've been lurking for a while though I've decided to share with you one of my projects. This project is actually being assessed as part of my course so please excuse the formalities.
Anyway here is my blog which has the entire project so far:
Read more…Hi all, I´ve been reading you for years in the shadows and not I´m desperated and need your help
Just build an F450 style quadcopter using a APM 2.6 board, last firmware updated.
Before you say it, yes, I have checked motor spinning directions and prop
Read more…