Hi guys! Sort of a noob and looking for some help. Trying to setup my quad with APM 2.6 and 3.2 firmware and when I am trying to do a compass calibration it shows compass 1 errors and compass 2 stays at 99 the whole time. So two questions:
1) Is i
Read more…Hi everyone.
Whilst flight testing a new platform, a control issue occured and the aircraft fell vertically with no forward airspeed into a heavy grass paddock from about 80 feet. Damage was relatively minor and the pixhawk looked protected by the alu
Read more…All,
I have an APM 2.5 that I bought more than 2 years ago at RCTIMER. It has been seatting on a shelf since.
I have trouble with the GPS, a GTPA010, I can't get it to work.
I have tried to use the MEDIATEK FW utility, but I always get a
I can use the mi
Read more…Hi,
I am going to set p my Hexacopter using Pixhawk and 3DR GPS but I wonder if it is possible to mount 3DR GPS mast on f550?
Has anyone any idea?
Thanks.
Read more…Here is the basic setup for my Quad.
1200 mm motor to motor frame.
Pixhawk Flight controller.
Castle Creations 50A ESC's
6s 15C Lipo Battery
AttoPilot battery monitor
U8 Tiger Motors
28" Tiger Props
Taranis 9XD Radio
Minim OSD with a 5.8 ghz video transmitte
Read more…I recently built a Sky Hero Spy 750 Y6. It is using Y6B parameters (AC 3.2) which after having it in the air a number of times is obviously not correct. The motors are KDE 2814XF-515. It seems there is a "RC FEEL" slider, does that affect the PID se
Read more…Is there a SDK for ArduPilot similar to what DJI provides? It would be nice to see a development environment that doesn't require to hard wire the source code.
Read more…Hello, I was testing a new airplane the other day, the maiden flight worked fine, no issues, landed changed battery and went again on the second flight I launched in stabilize mode and things were going fine so I switched to FBWA I had also done this
Read more…I have a Nova here that has never been flown that has one motor that isn't spinning. Given a voltmeter, etc. what is the best technique to determine if the motor/esc/or intermediate connections are at fault? Thanks!
Read more…Does someone know and can share what the difference is between the Altitude settings in Mission Planner for Relative, Absolute and Terrain. I know that the Terrain is for those planes equipped for terrain following, but what about the other 2 setting
Read more…I am in the process of setting up a X8 Skyhero 850 with Pixhawk flight controller. when doing straight waypoint missions there is a sharp twitch at each waypoint.
After a few waypoint flights yesterday I was thinking the Pitch and Roll I setting was t
Read more…Hi Guys
Most of us who are creating or using drone technology are into photography. Some of us make a living from it and lets face it we are all fairly passionate about our preferred brand of equipment. It does not take a great deal of expertise to re
Read more…Dear Dimitrius, we would be very happy if you honor our purchase contract.
The product has been paid since 19 November and all we know so far are two tracking numbers wrong that you have provided to us. I'm still posting here on the Forum because I th
Read more…Can anyone tell me exactly how the AR7000 is connected to the PixHawk. I'm having a disconnect with the instructions for a Quad X. Specifically where does the Aileron, Elevator, throttle, Rudder and Aux functions plug in?
Read more…I have Afro 30a escs and sunnysky v3508 700kv motors. They are having horrible sync performance with my new pixhawk. Flying with APM before they flew perfectly. I have just gotten this response from 3dr.
Santiago (3drobotics) Dec 03 02:16 PM Hey Jona |
Hi Guys
I want to try this new device rather than buy another 3dr leah 6.
What i want to be able to buy is a complete package ready to go, is this available in the u.k or Europe does anyone know.
Regards
keith
Read more…More and more RTF 'çopters are coming out with spin on prop adapters or even spin on props (DJI, et al).
The idea is no nuts or other tightening methods, the prop adapter spins onto the threaded shaft and self tightens due to the rotation of the motor
Read more…hey guys i have been flying arducopter 3.1 very nicely since today i updated to 3.2 and setup everything. After a few seconds of flight time the motor stops and the quad crahsed. Any idea what could have been.after r dovery one of the motor wont spin
Read more…Hi all,
I just found this link and it sees it is from 3DR as well:
Its price is 199$ which is cheaper than the pric
Read more…I have done what the wiki says to interface the PulsedLight LIDAR.
Then I set the proper parameters like range type to 4 for the Pulsed Light unit.
I do a write and it LOOKS like it saves.
Has anyone used the Pulsed Light unit yet?
I also noted the param
Read more…