google maps 3d
Is there a way to wiew a persepctive mode in mission planner (flight data) of terrain?
thanx in advance .
Max
Read more…
2 Replies
All Discussions (17281)
Sort by
Inability to load new geofence / flyaway troubleshoot
Hi everyone,
I had a geofence problem yesterday that resulted in a flyaway and the loss of an aircraft. I'd be grateful for any help identifying what I did wrong. I just moved across the US, and started my first flying day by creating a new geofence p
Read more…APM Power Module with XT60 Connectors Kit
The is rated for 18volts. I use 6s Lipos which will be over the specs. Is there any power module rated for say ...... 30V?
Thanks,
Brian
Read more…Advice For Project !! (Urgent Please)
Hi everyone ,
I'm currently in my forth year in Electronic Eng and I'm planning to build
a Quadcopter from scratch for my final year project . The quadcopter that I'm planning to build should be able to be control be Local control (RC transmitter)
Creating a dedicated camera photo logger with IMU, GPS, and trigger sensor.
Problem 1:
The APM .log files contain CAM messages based on when the autopilot commanded the camera to be triggered. It doesn't know when or if the camera actually triggered. This can result in CAM records that don't have corresponding photos or laten
Read more…Photography Quality - How To Measure
Many claim to have camera isolators that really work. But I've never seen data or evidence that is measurable. Help!
My brother Jim and I put this together, which I just tested on Rufous, the 1 1/2 hour + duration copter. We are trying to build a go
Read more…3DR Y6B out of control crash; flight mode error, just all around mess.
Attached is the log file and kmz. I did CompassMOT a few weeks ago and it was 4-7%. Vibration looks ok to me. It was a mystery and my first thought was ESC sync issue or motor failure but now I'm wondering if it was due to bad radio calibration causi
Read more…Georef Error in 1.3.9
Hi,
I have upgraded from1.3.5 to 1.3.9 and when attempting to georef my images I am getting the below error when using estimate offset:
Also when adding in what I think the offset to be and trying to pre-process anyway, I get the below:
Reading log for
Read more…Vision Based Landing Aid
I am working on trying to automate the landing sequence of a multicopter to help it land autonomously on a charging station. My thought is that the copter would takeoff, fly its waypoints, return and loiter over the launch area. From that point, a
Read more…ArduPlane License
Hello,
I have a few questions regarding the licensing of ArduPlane 2.x/3.x firmware that I would like additional clarifications even after reading GNU GPL3.
Suppose, i use the current firmware, make some changes to it like removing certain flight mode
SUGGESTED FAA REGISTRATION OF COMPASS & UAV
FAA_PETITION = REGISTRATION & IDENTIFICATION OF UAV & COMPASS:
REGISTRATION:
- COMPASS & UAV RC AIRCRAFT:
- FAA RESULTING:
- A US REGISTRY OF:
- DIGITAL COMPASS
- RC UAV AIRCRAFT
- A US REGISTRY OF:
- FAA RESULTING:
Read more…
- IDENTIFICATION OPTIONS:
- SERIAL NUMBERS REGISTERED & STAMPED IN TO HULLS
- UAV
pixhawk failsafe
a newbie question.
how set failsafe on mission planner on pixhawk when tx signal is lost, for rtl in place of land?
thanx in advance!
Read more…FAA Link with some interesting info
I am a newbie, and was looking through the Getting Started section and came across a dead FAA link. I suspect this might be the updated one with some great information, but also follow the related links on the page where it discusses rule 333 which
Read more…Will APM 2.x run on Crius AIOP V2
The APM 2.6 board & Crius AIOP V2 have identical ATMega 2560-16 microcontroller & same MS5611 Baro chip.
The Crius board has onboard HMC5883 Mag but this can be easily disabled by cutting jumper the same as APM2.6. The only difference I can see is th
Read more…Feature Request/Discussion: VTOL Flight Modes
Hi there, I had a thought about a potential way to implement VTOL in arducopter and I thought I'd open it for discussion so you guys can tell me how off base I am.
Some background just in case: I'm talking about aircraft like these, a flying wing with
Read more…Mission Planner question
Hi I am trying to setup Mission Planner 2.0.14 on a Mac. I have been able to install the firmware on my rig but when trying to follow the instructions found here http://copter.ardupilot.com/wiki/initial-setup/configuring-hardware/ and my screens are
Read more…Using SF02 Laser for auto landing - altitude sensing
Hi All,
Not sure if this is the right place to post.
We are testing the SF02 laser for auto landing and have it working and communicating and are now trying to implement into Arduplane code.
It looks like the altitude is updated through update_alt, but
Read more…Flying UAV's in Iraq for OIl/Gas
What are the rules/regulations around taking one of the UAV's into Iraq (Kurdistan) for use in Oil/Gas?
Is this legal over there?
Who would be the best group to talk to about getting one into the country?
Thanks,
Tenzin
Problems with Pixhawk I2C External LED
Hi,
Pixhawk running Arducopter 3.1.5
What can I say? Plugged the external LED in to the I2C splitter and no pretty lights. I have the splitter plugged into the I2C socket on the Pixhawk and the external compass is also plugged into it. The compass is
Read more…OSD Not Displaying Correctly
I've finally gotten to the point of getting FPV to work on my Y6. But the problem is the OSD does not display correctly.
My OSD is about 1 or 2 years old. My Y6, Gimbal and OSD are 3DR products. I've updated the OSD to the latest firmware. Not sur
Read more…
