Hello! :-)
I want to change the flight modes via de applanner without the use of the rc system, Is this possible? I want this, because I want to have all the 8 channels of the RC system free.
Thanks
Jesus
Read more…Hi,
I bought the:
- Arducopter complete kit (unassembled) from 3DR
- 3S 5000mAh LIPO battery from Hobbyking (here)
Problem:
While building from my Arducopter kit, while soldering/ connecting the PDB, I found that I did not receive a connector compatible f
Read more…On my quad, one of the motors starts just a little later than the other 3.
First I thought that the problem is the motor, so I changed it with a brand new one, but the problem didn't go away. Now I see that the ESC connected to that motor get warm - n
Read more…Does the Auto takeoff mode work? I have only tried auto land and have been a bit skeptical of Auto takeoff feature.
Read more…Hi,
I use mission planner in windows 7, never had any problem with it but today I started the update from 1.36 and right now when I try to start it shows a message that I need "microsoft framework 4.0" installed, but I've already installed 4.5 and it
Read more…Hi guys...
I have a notebook to run Mission Planner in the field, but when I am home, I'd like to use my desktop.
Is there a problem using two different computers like that? Will settings and such be synced between the two computers? (When Mission
Read more…Hello,
I have just finalized the construction of a 3DR HexaCopter and started the first trials.
As recommended I have programmed the 3-way button of my RC to Stabilize, ALT HOLD and POS HOLD.
While the first 2 modes can be saved to the APM I always get
Read more…Today I did a maiden flight of a Droidworx SkyJib that I built with an APM. It's an octocopter in coax configuration using Tiger 4014 motors and 14 inch props. With batteries it weighs 5.8Kg.
Upon take off it swung back and forth in what I think peopl
Read more…Hi!
Working with my quad but my 3DR telemetry system has a major drop in working range. I start to lose signal at about 30ft away from my laptop. Any idea how to start troubleshooting this?
Thanks
Dean
Read more…I was trying a very first basic configuration with APM 2.0 for altitude hold and loiter for my FY450 quad and I noticed that in LOITER mode with low wind, quad started little by little to lose its initial position making bigger and bigger circles aro
Read more…Loving FPVing my Arducopter. Still need to tune out some wobbles during turns - ridge winds dont help either :)
Read more…
Is there a problem with GRID V2? I cant get it to fill in the polygon, it only does a few points then returns home. GRID (V1) works fine...
Post with pictures showing what I mean:
http://www.diydrones.com/forum/topics/whats-wrong-with-grid-v2?xg_source
Read more…Hi DIYs,
I am looking for a Power supply for charging my 5000mAh, 3S 11.1V battery (3 cell) to be used at HOME.
I already have the charger Turnigy Accucel-6 50W 6A Balancer/Charger.
Would like to buy something affordable, from Amazon or similar place, t
Read more…Hi guys..
Can't believe I can't find this info (or why it wasn't included with the APM 2.5+?). What are the pinouts...both in and out, for the APM 2.5+ board?
Aileron, elevator, etc?
Thanks...
Read more…I was wondering if anyone has experience with the XNiteCanon near infrared camera, or any other of their infra-red cameras?
Thanks very much.
Read more…Hi everyone,
I would like to know what program could best be used to stitch Aerial Photos that have been taken in a sweeping grid together and even produce a 3D image of the ground similar to steroscopic photography that old cartographers used.
I know
Read more…Hi Friends,
I am having APM 2.5 in my RC aircraft and i need to measure how much power is being consumed by various units in the a/c like the motor, servos, RC receiver and the APM 2.5 itself. And i use Li-Po for powering up my a/c. And i use a power
Read more…I was just wondering besides a second unit, is there any point to an ardustation if you have goggles + OSD which id imagine has the same details ? Im just wondering what extra benefits does one have with this littel gadget.
Read more…