How many check boxes are ticked above? Not so easy to see...
Michael, please could the checkboxes be made black again like they were originally with a preferably a white background, the current white on grey makes it very difficult to see most of the
Read more…Hi,
I need to make my downward pointing camera to track a coordinate point on ground using 2 servos (x/y-tilt) on camera. Is this possible with current arduplane code?
How to configure it? For example when the plane loiters the camera would be pointed
I have started this dedicated thread at the suggestion of another contributor.
This issue has was raised on the main 'Arducopter 2.8 / 2.8.1 released' thread and can be viewed here.
http://www.diydrones.com/forum/topics/arducopter-2-8-released?commentI
Been doing this a while... been flying APM 1.. 2.0 for a long time..
Am I missing somthing... APM 2.5... ublox GPS....
no lights on the GPS....no GPS fix...
Did I hook it up right.. ? Thanks
Eddie Weeks
Read more…Michael (& the team?) did great job on this one, as far as I could see, it works flawlessly on Mono, it's the first release in a long time that works perfectly fine.
Thank you - Keep up the good work
Read more…Hi,
I have a new problem with the OSD, I can see all the OSD characters but it is frozen, no data changing, only the heartbeat symbol is blinking.
Any ideas?
Read more…Hi,
having some problems setting up second aileron on RC5, I found another issue:
RCX_DZ parameters for the trim deadzone are always lost after reboot APM 2.
I used firmware 2.65 and 2.66 programming over MP.
Any ideas? I am sure that I reseted/erased AP
Read more…Hi All,
All flights have stopped! All six of my motors are pulsating with no rhyme or reason. Now I'm afraid to fly at all. I've rebooted, reloaded, recalibrated, tried different batteries and even upgraded to the latest firmware 2.8.1. Nothing se
Read more…http://oceanai.mit.edu/moos-ivp/pmwiki/pmwiki.php?n=Main.HomePageFull
I was introduced to MOOS-IvP at a conference. The topic of discussion was JAUS & UUVs.
http://en.wikipedia.org/wiki/JAUS
AUV Simulation:
https://savage.nps.edu/AuvWorkbench/
Another sta
Read more…Hi,
Any ideas how I managed to plan a mission with 5 WP & 1 RTL commands which resulted in my hex ending back above home at 250m?
Switched from Stab to Auto when hex was at 10m elevation.
See screen print of APMLogVisualizer graph & MP Flight Plan.
Under flight planner, when we mouse over a location the Lat/Long reading will be shown at the RHS mouse location column. But for my note book the altitude reading remain 0 regardless where I point the mouse. In another desk top computer with the same
Read more…Is it possible to set the directory to be used to save logs? I have a small HDD in my netbook and the main partition is pretty full.
Read more…Hi.
I am setting up a new instillation of the Arduplane and trying to configure failsafe short.
I have set up and observed the channel 3 behaviour in the failsafe screen.
I have ‘taught’ the RX that the throttle can go to about 980ms and when I turn the
Read more…Hello guys, I'm another newbie to UAVs (and electronics to an extent). I was wondering, is it possible to power the quadcopter and all its parts such as motors via the APM2's usb port? I'm planning to attach a battery later on however it would be con
Read more…I have been gathering the parts for a UAV for a research project for a while, and I received my unassembled APM 2.0 with built-in MediaTek GPS kit in July, right before the APM 2.5 came out (it came with the parts for the voltage protection). Coincid
Read more…Here is a guide for setting up 6 flight modes on 1 channel of a JR XG8 eight channel DMSS RC transmitter. This is achieved while only using one of the active channel inputs (the Flap/Aux1 channel) & the Mixing switch (2 position). The result is the G
Read more…Hi,
I´ve recently updated my laptop to windows8 and dowloaded the APM planner 1.2.17 (ZIP versión since the .msi will not install) and it runs but when I try to connect the telemetry (Xbee) the process starts and then stops at the following screen:Aft
Hi All,
I finally got my Hexcopter back into the air this morning. After weather delays, overheating ESC, problems with 3DR Telemetry, mounting a gimbal and being stuck in NYC for a week (yuk).
The first flight went fine, I flew for about 9 minutes.
Read more…Im a senior at Virginia Tech in Aerospace Engineering, ive been looking to get involved in the UAV industry professionally but it seems like applying for jobs is limited to the big name companies. Do any of yall know of smaller companies that would
Read more…Q: will it fly? fly well?
I'm prototyping my latest design - got my motor mounts put together. Other than the plate in the middle, this is the only thing that isn't out-of-the-box... but could be made very simply if they prove to be robust enough:
Am
Read more…