Hi everybody,
I just loaded the new APM Software (2.8.1) on my APM 2.5 and installed a sonar (MB1260 XL-MaxSonar-EZL0 High Performance Ultrasonic Range Finder ).
Now the GPS doesn't work anylonger. The LED's on the LEA-6 keeps off and after a few secon
Read more…Hi Guys,
I was trying to build an IBCrazy antenna for my 900MHz 1000mW system, but the performance is very poor :( Tried 3 different types of antennas, but performance is Crazily bad.
If someone has a 900mhz antenna with an SMA connector(self-made
The mission Planner had a few up date but there is no info about what's new or bugs had fixed. Isn't it good to let user like us know more detail of every update so we can enjoy this wonderful program to the best it can offer?
Read more…This is a re post from category but no respond. I hope someone will help here.
I've connect attoPilot to APM 2.0 as per the manual. I also do the calibration. The voltage reading for my 4 s battery is correct but the current reading is either 0 A, 1 A
Read more…I had another great day out in the field yesterday. I was able to demonstrate a very stabilized flight with Alt hold and Auto.
One slight problem when the helicopter is going waypoint to waypoint there is a slight wobble. I am really not sure which PI
Read more…A question for experienced designers/aerodynamacists:
I have built and flown my third own design twin boom pusher plane. All 3 are very similar in dimension and proportion.1.7m span, 1.3m length, 1.3kg weight, Clark-Y airfoil.
However from the previous
Read more…with lots of new snow, I decided to test recovery time needed to stop the fall if motors stopped during the flight.
I did it the way I see this accident to happend. - while in loiter, I took the throttle stick all the way down, for descend - then - s
Read more…If you go to Arducopter Pids and change Altitude Hold/Altitude Error:/P, it shows up immediately in the Arducopter Config/Altitude Hold/P spin-dial.
BUT.... If you change Arducopter Config/Altitude Hold/P, it never shows up in Arducopter Pids/Altitud
Read more…Trying to power my APM 2.5 from the output side, I've installed j1 jumper but only have 1.4v at the fuse as shown to measure here: http://code.google.com/p/ardupilot-mega/wiki/APM25board. I can power it via the output bus but would prefer not to.
Any
Read more…Hi all,
My lovely wife bought me a simple gimbal for my quad and surprised me with it and a GoPro (told you she was lovely). I know nothing about this stuff, so thought I would ask for help here. The gimbal only has one servo - for tilt. I am unclear
Read more…I've connect attoPilot to APM 2.0 as per the manual. I also do the calibration. The voltage reading for my 4 s battery is correct but the current reading is either 0 A, 1 A or 2A. That's all it show. Anything went wrong ?
Thanks for your help.
Read more…How many check boxes are ticked above? Not so easy to see...
Michael, please could the checkboxes be made black again like they were originally with a preferably a white background, the current white on grey makes it very difficult to see most of the
Read more…Hi,
I need to make my downward pointing camera to track a coordinate point on ground using 2 servos (x/y-tilt) on camera. Is this possible with current arduplane code?
How to configure it? For example when the plane loiters the camera would be pointed
I have started this dedicated thread at the suggestion of another contributor.
This issue has was raised on the main 'Arducopter 2.8 / 2.8.1 released' thread and can be viewed here.
http://www.diydrones.com/forum/topics/arducopter-2-8-released?commentI
Been doing this a while... been flying APM 1.. 2.0 for a long time..
Am I missing somthing... APM 2.5... ublox GPS....
no lights on the GPS....no GPS fix...
Did I hook it up right.. ? Thanks
Eddie Weeks
Read more…Michael (& the team?) did great job on this one, as far as I could see, it works flawlessly on Mono, it's the first release in a long time that works perfectly fine.
Thank you - Keep up the good work
Read more…Hi,
I have a new problem with the OSD, I can see all the OSD characters but it is frozen, no data changing, only the heartbeat symbol is blinking.
Any ideas?
Read more…Hi,
having some problems setting up second aileron on RC5, I found another issue:
RCX_DZ parameters for the trim deadzone are always lost after reboot APM 2.
I used firmware 2.65 and 2.66 programming over MP.
Any ideas? I am sure that I reseted/erased AP
Read more…Hi All,
All flights have stopped! All six of my motors are pulsating with no rhyme or reason. Now I'm afraid to fly at all. I've rebooted, reloaded, recalibrated, tried different batteries and even upgraded to the latest firmware 2.8.1. Nothing se
Read more…http://oceanai.mit.edu/moos-ivp/pmwiki/pmwiki.php?n=Main.HomePageFull
I was introduced to MOOS-IvP at a conference. The topic of discussion was JAUS & UUVs.
http://en.wikipedia.org/wiki/JAUS
AUV Simulation:
https://savage.nps.edu/AuvWorkbench/
Another sta
Read more…