For anyone who has needs, till next 14 days, you can buy the following items at lower price:
ITEM: NTM Prop Drive Series 35-42A 1250Kv 600W
LINK: http://www.hobbyking.com/buddy.asp?code=7E877C0D-FDF0-467B-AA70-D4E29EE9BA6E
you will pay $12.10 instead
Read more…In simple and stabilize mode (have not tried anything else yet) all tests are good - quad resists moving it from horizontal and left and right stick, yaw input and vertical input from radio all behave like they should.
However pitch towards me tilts t
Read more…After updating Mission Planner to 1.0.50 I have a graphic bug while switching beetween "Action" and "Gauges" tabs. I attached screenshot for better understanding the issue.
Read more…The IMU contains sensors on the surface. I am right now deciding to put the 5.8Ghz transmitter in between the space occupied by the GPS receiver and the IMU.
Question: Will the heat generated by the A/V transmitter affect the performance of the GPS a
Read more…Hi, Has anyone tried the UDP function ? We have a long range requirement and will be using a TDMA data radio. We need to receive telemetry and control the air frame's speed and direction. Please let us know if you have had any experience with this
Read more…Hi, Can anyone tell me how often QGroundControl writes to disc ? Would like to use a computer without a hard drive to save power. Thanks !
Read more…Whilst spending a lot of time on this project I found a way of distracting the kids a little bit and giving them a helping hand in designing a new hood for the arducopter.
Its made of styrofoam and canbe painted by the kids.
Hy all
Today i have flown my drone for the first time in AUTO mode. Basic 4 point navigation route. The throttle sounded so strange (i am talking about fixed wing airplane)... every few seconds it turned full throttle for a fraction of a second and s
Read more…I tried to update to APM Mission Planner to version 1.0.50.
It now fails to start and wants to send a dump to MicroSoft
I reloaded version V1.0.46 which was working before, and that to fail to start with the same message.
I have tried to install latest
Read more…I'm trying to build an X8I'm able to have 6 motor running with the APM_RC libraries but I don't understand why the last 2 are not spinning.So, since I looking in many repository everywhere, :) I found in ardupirate, the config.g herehttp://code.googl
Read more…I recently posted that my quad was acting strangely in simple mode.Basically it wold move left and right on commands from the radio but reversed backwards and forwards.I forgot to mention that I was not using a gps.Not sure that this matters.1. What
Read more…My problem is thus.. Using Megaplanner 1.0.49 and on the serial port to program the APM all works fine. Loads the hex file and verifies ok. I run flight data and all is well. 7 sats GPS ok google map ok !! works GREAT.. However...
I have a pair of xbe
With ardupilot mega how do I adjust travel limit when using elevon mixing for a wing?
Read more…I have been using my Ardupilot Mega Plane with the Rc mode switch positioned in Manual, Stabilize and RTL. It is working perfectly when I move my switch back and forth between modes. Now I want to move to Auto Mode using the Mission Planner and start
Read more…
I'm working since a couple monthes with Mega planner to check for Radio inputs (Arducoder project).
Regularly, i can see crashes, most of the time after reconnecting to the APM board, and if the software are has been run a long time before.
After ea
Read more…Hi!
I've been having a back and forth with Michael Oborne on why v1.0.20 of the mission planner works but v1.0.48 does not ()http://diydrones.com/forum/topics/v20-works-but-v48-does-not!
No luck so far on resolving it. I am making a post here just in
Read more…Hi All,Is is possible to design a UAV that uses its entire body as a rotor during take-off ?Concept :In this UAV vertical take-off does not require an external rotor or a thrust/weight ratio greater than one. When this UAV reaches a safe altitude, it
Read more…Fantastic!
My hexa was hoving well in 2.0.33 with default PID except D was doubled to 0.24
But when I tried that configuration I was getting high frequency oscilations on the roll axis. After some trials I went to the default PID and its great!
So t
Read more…This might not be so much of a problem, but something that is puzzling me.
I followed the steps exactly as specified here. This worked perfectly..I even went as far to reprogram it all and set up the switches in a logical pattern. Again, no problem,
Read more…Hello
Do you have any source code to set the waypoint manually about Ardupilot 2.3 program?
I tried modified the Manual waypoint program of Ardupilot 2.6, but it doesn't work on my hardware.
Thank you
Read more…