Hi Everyone,
CAUTION: Before actually mounting propellers make sure to test the motor operation to assure they run in the correct direction, else swap two leads on the specific motor to reverse its rotation direction until all match the picture. Wait with install
Read more…Good evening, I just got my system set up but I'm having a problem with the GPS. I have the MediaTek MT3329 and I'm running Ardupilot 2.7. The MediaTek appears to have a GPS lock (the blue light within a minute or so goes a solid blue). The shield
Hi !
My Quad already flies with Arducopter_alpha_RC1 software, but without activating GPS nor magnetometer that are mounted on quad (but not supported by this SW release).
=> Do you know if ArduCopterNG is already capable to be installed to fly, eve
Read more…Just wondering if there were any future plans to send PPM (RC signals) through the data modem up to the plane. Could see this being useful because it would allow for greater distances to be flown since high power options are more readily available fo
Read more…Honestly, I've never flow a rotor craft before, but I just got this thing in the air for a brief few seconds today.
Hi guys
how are you forum ? do you remember i had a crash a few weeks ago?
Last weekend i went to the flying field to test the airplane after the crash, redesigned the tail, and i had to make some testing with the motor washout and control surfaces moves.....
My MTK GPS arrived and I upgraded it for use with Arducopter.
I get a nice 3D fix when outdoors.
Now I would like to get the GPS info over XBEE to use in a ground control station.
Xbee allready works with configurator at 115200bps.
Any suggestions?
Read more…
Guidance please,One M2MPower ESC will not see the Receiver (AMP not in loop yet) - so just beeps away (Alert tone 2) - the rest armed perfectly - so I assume its faulty - will have to get another one - Agree?I have some other escs around - can you mi
Read more…Is there a ground station with working GPS location and stuff like that for arducopter? By Ground station, I mean a software version.
Read more…Everything work ok otherwise. The 4 motors run correctly, the sensors all check out.
I have a Corona digital servo that works when I plug it into the receiver or output channel 0.
On output channel 4-7 I don't get anything.
servoMotor = constrain(APM_R
How do I know what mode I am in when I use the switches for GPS hold (on/off) and acrobatic/stable mode? I have telemetry data coming in, but is there a way to display what mode I am in so I know which position of the switch is the right one? And my
Read more…Hi there. Im currently designing Autonomous Quadrotor as my final project at school. Everything was good so far until trying to find PID parameters.
I have a question and some concerns about suppyling power from Li Po's. As you know brushless m
Hello,
First of all I would like to say Thanks to the DIY team for such a great
product.
Quick question, I received my Arducopter just the other day, however,
it appears that my arms are missing holes for the ESC cabling to go into??
Jani, was this inte
Hello I came up with this way of installing the ESCs that I found makes for a neat tucking away of cables. Doing them one by one I noticed that by having the cabling take a natural route around the power board my routing ended up so that while an ES
Read more…Where can I find info on spec'ing out my motor/prop/esc configuration. or can someone tell me what the typical setup would be for a 24" motor to motor quadcopter carrying, camera, telemetry, video radio, etc. basically all the options for electronic
Read more…I was wondering if anyone knows what size battery is compatible with the stock motor and ESC that comes with the Dynam Hawk Sky?
Thanks!
Read more…I want to get into it, but I cannot find a place where they tell me, which parts do I need , and which ones are more recommended
I would like to get info on:
auto pilot
gps module
pc communication
etc
thankd guys
Itay
Read more…