Apm 2.6 ezuhf ppm
hi,
Is it possible to connect my ezuhf diversity receiver to the apm 2.6 using only one servo cable(ppm i believe it is called). This will be great if it is do-able.
Read more…
7 Replies
All Discussions (784)
Sort by
frsky taranis
hi,
I recently bought a frsky taranis. Am i supposed to use the frsky firmware on their website or should i goto the opentx website and get the version there(which is much newer).
Thanks
Damo
Read more…Minimosd
I purchased the Minimosd from 3D Robotics and everything is wired and works between my quad and FPV. My problem is when I go to the Minimosd-Extra to configure the panel layout on my PC. I keep getting the following message. "Failed to Upload New
Read more…915mhz patch
Does anyone know where i can get a 915mhz patch antenna so i can extend my 3dr telemetry range.
Read more…DO SET ROI and/or strange automission pathway between waypoints
I tried an DO SET ROI auto mission , planning my waypoints more or less in a circle around a point of interest :
The take off point (home) is in the circle, so the drone should first get to the first waypoint by travelling more or less along the
Read more…Same pitch and length props .which better?
http://www.foxtechfpv.com/1755-mkii-carbon-fiber-propeller-cwccw-p-1159.html
http://www.foxtechfpv.com/1755-carbon-fiber-propeller-cwccw-p-692.html
What are the differences in performance from these two props? I have 460kv motors; which is better?
Tha
Read more…What does this prop combination mean ?
I am having issues with my quadcopter in that it is taking about 70% throttle to hover. it was working fine before on the same weight but different motors and props. After replacing almost all components over the past two months (as i did not know th
Read more…Arducopter issue
Hi,
i had posted an issue where my quad was not flying well. Now i got a new frame and started afresh. i have been very careful in setting it up. The quad hovers well on a new battery but then after about 2 minutes it drops altitude. yawing left drops
Read more…How on earth do you use droneshare ??
I must be very stupid but I can't find how to upload logs on droneshare. This is the screenshot I get : can't find any button, no right click menus, no nothing to upload a log...
Am I in the fourth dimension or what ?
Read more…What screws are these ?
Hi,
Do you know what screw sizes are in the image below (i also highlighted where they go)?
Here is where i bought the motor but i need to get more of the screws
It's really annoying that the frame i bought doesnt have the screw holes for eith the moto
Read more…Do you know future of Small UAV Market by the end of 2020
Small UAV market will make healthy growth with rising applications, innovative technologies and demand for sensor payload products. if you want more details you can read it here
Read more…Battery Failsafe (RTL) crash
While flying my APM 2.6, my quad went into RTL. Based upon my log, the RTL was triggered by the low voltage (10.5). Although, I don't understand why, because I had the failsafe options disabled.
I was flying my F450 in the woods so I didn't want the
Read more…Loiter Problem with low % of compassmot
Dear all,
I have been struggling with loiter issue for some days now and somehow I feel stuck. I have been searching all around and trying everything I could find, but seems like my issue is not yet resolved. I have built quad with APM 2.5 and Ublok 6
Read more…About mission planner error and please help me for a mission planner code compiled
I have download mission planner and setup visual studio 2010,then start trying compile,but there are many errors.Could anyone have compiled the code give me your mission planner code compiled,that will be the biggest help for me,that save me a lot of
Read more…Changing 3D Robotics frame to Tarot FY680
I bought a 3DRobotics hex Y-frame kit. Now considering changing to a traditional hexa and using Tarot FY680 IRON MAN 680 Hexa-Copter Carbon Kit. Anyone have experience of this?
Read more…Motor or ESC issue?
Hello everyone,I have a problem with my 3dr DIY Quad (running latest release) with mission planner 2 (Mac) setup with Taranis + X8R.Motor #2 does not want to play ball.With Pixhawk armed, prop does not spin like the others until a gentle throttle app
Read more…How can I using copter measure wind direction and wind velocity?
I want use copter measuring wind direction and wind velocity,could anyone give me a suggestion ?thank you very much.
Read more…yaw not operating correctly
on my quad, pitch,roll and throttle are working fine. When in stabilize the yaw appears to have the effect of moving along the 5oclock to 11 oclock axis, although i have to land fast before it crashes. In stabilize with simple mode enabled the quad i
Read more…ESC Calibration
Hi All
I have been struggling with this for a few months on and off but I have been at it full on this past week and I have got nowhere!!
I go through all the usual steps and after the long monotone note, I press the arm button and noises are made, wa
Read more…