In an attempt to understand the absolute full extent of the battery payload, a field operator had conducted a test allowing the copter to loiter until it "fell" from the sky. I know, I cringed hearing this also. The following days flight resulted i
Read more…I need some detail information about building quadcopter using msp430 launchpad.i have already bought launchpad kit.please suggest me asap
how to install the firmware to that particular launchpad?
which software can be used for this types launchpad ki
I have tried everything from
1) Repositioning the GPS
2) Recalibrating (about a billion times)
3) Added ferrite ring
I just don't know what to do at this point but maybe buy another GPS
Its a uBlox GPS
Does this in Alt Hold or anything GPS related,
Stabiliz
Read more…I say unexplained , although i actually caused the crash. I was mapping a test area that I frequent. The flight went well but at the end during the final stage of the return to launch, the aircraft stopped descending at 10 mtrs and held there. I tho
Read more…I have built several quads with the pixhawk using an AR6210 Rx and the 3DR ppm encoder. Had an issue with one today that is baffling me. The Rx is getting power through the encoder. The monitors on the "radio calibration page are green (but no input
Read more…I want so reduce the speed (deg/sec) on the Yaw Axis controlled by RC and Auto Mode.
I was trying the Parameter "Rate Yaw P", "Stabilize Yaw" and "ATC_SLEW_YAW" but I did´n recognize any change.
Please can someone tell me how to adjust the Yaw speed?
I
Read more…Hi all,
I'm experiencing some weird problem with GPS.
I have used my APM on a plane with no problems. GPS (MTK one, from Adafruit) is hard-wired (soldered to the board directly).
Now I want to use this APM with GPS on my hexa. Nothing was changed but fi
Read more…I have enclosed both the declination of my site as well the which error is pop ups every time.
Still once i entered like this it is automatically changing to 0,-28 please help me out changing the declination in the negative or any other process are pr
Read more…I have the solar panel plate the description follow below
Maximum power (PMAX)- 5W
Voltage at maximum power (VMP) - 17V
Curent at maximum power (IMP) - 0.8 AMP
Short circuit current (ISC) - 1.3 AMP
Open circuit voltage (VOC) - 12V
Maximum system voltage -
Read more…The NAZA has been removed and replaced with an APM Mini, thought I'd share some of the progress.
There is some tuning still need to be done, the NAZA had no wobble once I changed some settings, hope I can get this one as good.
If you like you can make
Read more…Hi all,
I finally got my multicopter built and I am trying to connect my JR XG8 receiver to the Pixhawk PPM port directly. I have been using a PPM encoder but I would like to ditch it. Has anyone been able to successfully run their quad with a JR xbus
Read more…Hello Friends,
I am having a strange thing happen here.
I have been flying my APM 2.6 for about 6 months on various frames. It works great. The last month or so I have been flying V3.2R10 It worked great.
I mounted the APM on an F450 frame and put 3.2 o
Hi,
Attached is a dataflash log from my APM 2.6 running the latest firmware. I flew for ~ 12 minutes but most of the data is missing ?
See the image below and the log is attached.
All my logs have missing data.
thanks
Damien
Read more…Unless I'm mistaken I feel that diydrones would rather all flights use a Tx, but are we not very close to a point where we can to put an end of the Tx for drone multirotors as the primary flying device. After all this is 'diydrones' not 'diyrc' and
Read more…I am looking at making a new LEGO drone project, this would be my 3rd one
1st one used APM 2.5
2nd NAZA
I loved the APM functionality and NAZA small size, now I want to put them together
Because I don't think 3DR officially sells a Mini APM 2.6 and I wan
Read more…I have a hexacopter I have make an so many RTL'S with the altitude of 5 in the flight plan it done perfectly when iam setting into the auto mission its not getting the required altitude which was 5 default alt . I have reinstalled mission planner no
Read more…Hi Everyone,
I´m seeking assistance to adopt ArduCopter further towards autonomous surfaced and submerged operation of a Russian Oscar II class RC submarine. I have successfully managed to run the boat in stabilize mode in the horizontal plane for cou
Read more…hi have a pixhawk on my quad and ive been though the setup 4 or 5 times now and still end up with the exact same issue now. I have done a compassmot motorsync and rc cali and everything else needed. running the latest firmware ie 3.1.5 and have chang
Read more…Hey,
Having problems with different rpm values on the motors even after the ESC's are calibrated and APM is levelled. The problem first occurred after my last crash and at first I thought that the problem was in ESCs. As the frame was a bit damaged a
