Hi all,
I couldn't connect the APM 2.6 to mission planner. I don't know where the mistake is ? I downloaded the latest version of Mission Planner and plugged the APM 2.6 to the PC then I chose "Install Firmware" and firmware was installed. Next, I cho
Read more…I recently took delivery of an APM 2.6 flight control and an M8N gps/compass module.
The wires on the module are only about 7" long and are not long enough to reach the mounting pole. Has anyone ever extended these wires by soldering in extensions or
Read more…I have a pixhawk fc and a turnigy 9x with a PPM encoder.....my problem is i am unable to get the 3 position switch to work.........works fine with my APM builds.....i am currently using my Cheerson cx-20 TX/RX and it works fine on the pixhawk....all
Read more…hi all
Got a bit of an odd one going on here.
I am trying to configure the Fail-safe option, Mission Planner/Pixhawk does not detect when I turn the radio off so it will not trigger Fail-safe.
If I start mission planner with the radio turned off, it cor
Hi
Need a little help please
In Arducopter v3.3 it says that Auxiliary functions or now supported on Channel 9 to 12.
I have a Ten Channel system connected and although I have enabled option for Channels 9 & 10 they don't work, Channels 1 to 8 work fine
Read more…Hi,
could you tell me who is personally, legally accountable in case of drone crash case reported to law enforcement officers, FAA due to known bugs, flaws in Pixhawk flight controller ?
I have followed tens of discussions on this and other forums and
Read more…Hi,
I like to thank all developers for their tremendous work giving me and all the other users so many opportunities and fun with ArduCopter, Plane, Rover and PX4.
Now I have two questions I could not answer myself although following this forum quite a
Read more…Hi all, I am trying to make a hexacopter with using APM 2.6 and I want to use FPV on it. But I couldnt figure it out where should i buy FPV equipments. And the next problem is the control of cemare. I mean how can I control the camera? Do we use Miss
Read more…I am using Mission Planner with Arducopter 3.2.1 on a Iris+. I keep looking at upgrading to the latest version. I like some of the new features like BRAKE, but don't want to mess up anything that I have now.
Is 3.3.3 stable?
Is there a list of changes
Read more…I'm building a quad copter with an APM Mini 3.1. Using Mission planner V1.3.35 and AC v3.3.3 firmware, although the banner on the mission planner screen displays AC V3.2.1.
I verified that the individual ESCs and motors respond to PWM signals from the
Read more…Now that the LidarLite is off the market (until Garmin brings it back), there are not many options for accurate altitude sensing.
I have a optical flow sensor that I would like to mount up, but I don't want to spend $250 for the Lightware SF11, or $23
Read more…Hi All, ( PixHawk QuadX FW 3.2.1 MP 1.3.35 )
(I hope this topic is in the right forum?)
Is there a Param / Value to adjust for the time it takes when one issue a Radio DisArm Cmd to when the motors actually stop spinning.
By observation I see this time
Read more…Hi I'm new here
I'm building a octocóptero I need this lift enough weight then I'm getting engines running at 6s 22.2 v battery with drive 2800 grams per axis, but I encounter a problem, the power module only supports 4s Battery 14.8 v with this the
I have been working on this setup for a while now.
The heart to it is the custom code I wrote for the ESP8266 to serve as a UART - TCP client that connects to a server in the internet. The GCS connects to the same server. The server is running a TCP r
Read more…I put together a prototype Arducopter controller with APM 2.6. It's been programmed for quads. Please see pic.
Can I test only one motor, or does the controller need to see all four motors connected?
Thanks in advance.
Hello everyone!
I need to get range data from a couple of sensors (at least 4) into the Mission Planner. I was able to connect one analog sensor and get range data from the sensor accurately, but I do not think Mission Planner has the necessary vari
Read more…We are Airborne / ISR Technology Company in Colorado, USA. Our company ShadowAir Ltd. would like to connect with you for Joint-Venturing / Partnerships for Projects & Contracts. Could you please let us know how we can assist you for Rescue Operations
Read more…I am using 3.3 and have changed the RC_FEEL_RP param from 50 to 35 for a gentler response to my inputs.
Do I need to reset this to 50 before attempting Autotune? Since there are no inputs from the radio during Autotune I would assume not.
Robin
Read more…My micro quad is rolling to hard right, I have to full left stick to get it to hover in the slightest.
Mission planner everything looks good with the accelerometers, artificial horizon is all showing correct.
CG has been checked and very well balanc
I'm working on a project that consists control APM with voice commands using the EasyVR shield of arduino. I'm talking to the APM through a C++ program that interprets the voice and sends MAV commands to APM.
The problem is: I' dont know how to send a
