Hi,
I have developed a library that allows DroneCell to be used with APM. That part works fine, however there are massive problems getting the stock mission Planner to
Apparently MP was not m
Read more…This is the quad.
http://diydrones.com/profiles/blogs/mk-ii-h-frame-quad-now-flying
It is 2.2kg, using 4s 5Ah battery
I have been using these motors for some time now.
http://www.fast-lad.co.uk/store/products_multicopter_motor_4008-530kv_w/400mm_cable_95
Read more…Hi all, can someone confirm what acceptable compass offsets and mag_field are?
I've been trying to improve my compass accuracy lately (3DR Quad C), and had a bit of a win today by raising the APM platform higher to get away from the battery wires conn
Read more…Mike ok I apologist and I might have been wrong to assume it didn't get out of Malaysia which in most case lots of news doesn't, but it still doesn't warrant a reply "It is the mission of DIY Drones to only promote the positive side of hobby drones"
Read more…This is the second time... First time burnt 1 Hitec servo, this time 2 Hitec servos
My setup:
Powering the APM 2.5 from two power sources, both 5v (removed JP2 of course)
Heli: Futaba RX with 3 - Hitec HS 5245 MG for the collective, 1 Futaba S9275 (its
Read more…Hi all. My first post here, but I've been lurking for a while.
Building my first Quad (3dr Quad-C) and have been having a heck of a time. Right now the problem seems to be with two of the 3DR ESCs. I can't get them to calibrate, or even respond to pow
Read more…I have an APM2 with latest firmware. If I switch to stabilization mode, then when I open the throttle the elevator moves gradually up and ailerons move so that the plane would climb and bank right.
Am I missing something?
It doesn't do it with stabilai
Read more…This looks interesting. Anyone built one, or used gopro in this way? Any feedback?http://gopro.com/3d-hero-system-tech-specs/
Read more…I thought it might be a good thread to discuss the basics and a little more about what goes into building a MultiCopter. I am new to this, so I have nothing to offer except my inquisitive nature to get a discussion going. I'm hoping this might become
Read more…Hello everyone!
Is it possiable to make copter fly less agressive in auto mode? When I fly missions it really scares me sometimes. Can it be done by tuning Navigation PID? And one more thing, I went through yhe forum but couldnot find how to make copt
Read more…I've asked this same question over at multirotorforums.com given everyone there seem to be flying high end commercial gear, but I'd like to hear from the DIY side as well.
Any opinions on using APM2.5 or the PX4 as a flight controller for a commercial
Read more…Just got some of these http://www.himodel.com/electric/HiModel_Cloud_Series_C3410-_520KV_Outrunner_Brushless_Motor_for_Quadcopter_Multi-rotor_Aircraft_shaft_reversable.html
To replace my other 530kv motors.
Faults listed in order of discovery.
Initial
Read more…Looks like I will end up getting a laptop for mission planner. As MP is all I need it for, I can't see investing a lot of money to run it. What is a reasonable minimum platform to run MP
Read more…Hello, i am wondering what the distance from the border a diy drone would be allowed to fly. I am 20 miles from the border at home in North Dakota. I can't seem to find the right links.
Read more…I'm new to the ArduPilot, and trying to tune gains for the first time. I've got the plane flying pretty well in stab mode, but when I switch to FBW-A it is extremely lethargic. It flies straight and is stable, but a full stick-deflection in roll only
Read more…Hi all,Another newb here, and I thought I'd approach my new project with some deserved caution.My goal is quite simple, and not unique - to build an autonomous camera platform to use to shoot some HQ aerial scenes for my wife's new training program,
Read more…My quadcopter is set with standard speed parimeters. In Stabilise the quad moves exactly how I want it and at the right speed. In Auto it goes OK but fights the wind (as little as 15mph winds) and almost comes to a hover. Do I increase the mps in the
Read more…I am working on a project for surveying oyster beds for a local oyster company. I need to be able to have a flight plan using GPS to fly over the beds and take pictures. However, google maps GPS data doesn't match up perfectly with the actual locatio
Read more…I just bought a flying wing i want to use the apm 2.5 on for stabelise and rth. Only problem is i can;t mount the apm center. I will be about 7 cm off center to the left. Is this possible or a no go?
Read more…