Arduimu V3
I have a V3 arduimu but I can not install the GPS and my GPS is model GT 320R, what can I do?
Read more…
0 Replies
All Discussions (17289)
Sort by
Surveying long line beds for a local Oyster Company.
Recently I have been talking with a guy from my home town who owns a local oyster company. Every couple weeks/month he has his workers boat out to the oyster beds during low tide and they are patches of 10 acres or so and they have to walk in the mud
Read more…Gas powered Hex, stuck on the ground
OK.. I have built 10-15 tri,hex,octo… ect all with AMP 1 2 2.5…
All worked fine…for the most part..
Now I am building generator-copter… 23CC gas motor powering a 2000 watt brushless motor..
To date the generator has produced over 1100 watts….
Read more…APM 2.5 mid flight reboot
Hi guys, my APM has recently started to reboot mid air for no apparent reason. This first happened on the 9th March when I was flying in stabilize mode and all the controls just froze (no response to RC tx, servos all locked, telemetry reporting no d
Read more…Grid missions for mosaics
Hi, I was experiencing with Ardupilot in HIL, and give I try to the grid missions. My plane fly very well any kind of mission, but when I create a grid it's doesn't follow the waypoints very well.
What happens is that when the plane finish a line of t
Read more…Brand New APM 2.5 Magnetometer/Compass Fails
i tried for 6 hours trying to figure out what is going on. i wanted to use this APM 2.5 for hardware in the loop simulation but i think the compass is short. there is no physical damage or any visible damage on the board that i would see... i just pu
Read more…Drone seen near airport - JFK
In consideration of the FAA's rules around using RC aircraft around airports (see link to story below), is there a way to import aviation sectionals into APM Mission Planner so that one may be sure to stay away from any and all controlled airspace?
Read more…Voice Controlled APM 2.5 Project
Is this a project you would like to tackle as a community and is this a project you would like to see become more serious?! As a community would you like me to build a discussion or group around this project?! Let me know what you think.
Read more…Loiter doesn't stay overhead
Hi,
Just got my wing with APM 2.5 flying. Stabilize works great, but Loiter just sort of flies away. The plane will circle overhead, then the next circle is a bit further down wind, the next circle is so far away I have to switch to manual and fly it
Read more…Arduplane: Using battery voltage in flight plans
Hi,
I think it would be a very useful addition to add "until battery voltage = xxx V" to the loiter parameters in flight planning. That would - naturally - require a voltage sensor but it would be quite useful for autonomous flights. Especially, if th
Read more…No telemetry on HUD in APM Mission Planner
APM Mission Planner HUD attitude indicator is working great but there is no telemetry ie Altitude, ground speed, heading and etc on the HUD display. I'm running Ardupilot APM 2.5 and Mission Planner 1.2.36 on a Dell Windows Vista Optiplex 330 that
Read more…APM in comparison to commercial offerings
I'm considering purchasing a Droidworx copter to do aerial photography. I love my 3DR quad and hex but I think it's time to move up to something purpose built for photography.
So now I have to make a decision about flight controllers and the only expe
Read more…Alternative Multicopter Autopilots
Firstly let me caveat, this discussion is not intended to be critical in anyway of APM. APM has moved ahead in strides and I acknowledge the great work of the developers and contributors in this forum.At the moment I am looking to get constructive fe
Read more…Fly-By-Wire Low Altitude Limit, only for FBW-B ?
does the Fly-By-Wire Low Altitude Limit function only work for FBW-B or does it also work for FBW-A? I don't have an airspeed sensor so I can only use FBW-A. or is there maybe any trick to make it work for FBW-A? this would be a great safety function
Read more…Strange behaviour in AUTO mode, 3DR Hexacopter.
Hi all..
After several successfully flights with 3s lipo and standard PID settings i decided to change out my 3s with 4s 5000mAh batteries.
But something stranges happen during waypoint flight in AUTO mode.
It was set to climb 150meters in a 1km flight
Read more…Restoring APM 2.7
I'm setting up my APM on a bumblebee carbon fiber frame. I have discovered that the 2.7 firmware works fine with the frame and I am currently running 2.9.1. I would like to restore to the 2.7 firmware. In the firmware tab when I click on pick previou
Read more…RSSI Logging?
My receiver outputs received signal strength and I have connected this to the A0 pin on the APM. I have set the RSSI_PIN paramenter appropriately and can display the RSSI correctly in the MP while the quad is attached to my PC. Is there any way I can
Read more…CH6 Tuning doing something weird!?
I have previously used ch6 to tune individual parameters without any problems. Recently I have attempted to fine tune alt hold using the same method but now when I attempt to configure ch6 to alter any parameter, I get unexpected results.
For instance
Read more…Mission planner update 03/16/13 1.2.36
Guys:
Today when I started the mission planner I received a notice of an update. I updated it, but how do we know what was updated?
Thanks!
Bret C
Read more…De-shaking, editing frustrations gopro.
Hi.
There must be thousands of people doing exactly what I am trying to do so am seeking advice here.
What I would like to do-
-Download the MP4 from my gopro (hero3, using 1080p 5-fps at the moment).
-Use some software to reduce the shakes.
-Perhaps tr
Read more…