at altitude 700m happened auto disarm
but at 600m has been rearmed (using mission planner)
log file attached and here:
http://forum.rcdesign.ru/attachment.php?attachmentid=800343&d=1369771587
russian discussian here:
http://forum.rcdesign.ru/f123/thread23
Read more…hello,
I had the arducopter outside my house running perfectly in simple mode. I ran in the same location for a few days with no issues with simple mode.
Tonight i drove to a new location about a mile away and when i enabled simple mode it was 90 degre
Read more…Hi Everyone,
I would like to get some high intensity strobes going on my APM 2.5 While I can handle the electronic side of things, I am a bit confused with going about the code to drive them. There appears to have been a change in code around V2.6 (ma
Read more…Hello,
I have tried to hold altitude "manually" in stabilize mode, APM2.5, V2.9.1b, quadcopter.
When I have the throttle stick at about hover, I try not to touch it. I used expo on my radio to make it easier to find the right stick position.
Then I try
Read more…I have been following the wiki for APM2.5 camera gimbal setup (using firmware 2.9.1b, quad X).I have no problem to use RC10 or RC11 to trigger a servo as camera trigger (using receiver ch7 as manual input).However i do not get any joy using the other
Read more…After 30 to 45 seconds I begin to loose control of the copter. I am not sure if some of the updates changed some of my settings, or I screwed something up.
I placed a brushless gimbal to the copter and I don't know if something from that is messing
Read more…Hello,
In the APM2.5 configuration, for quadcopter firmware (not hexa, not Y6, etc), how is Channel 8 input of the receiver processed by APM ?
I would like to use Channel 8 to use a servo. How can I configure this (without modifying the firmware in APM
Read more…Hello world.
Firstly, I'm new to this (oh great I can hear everyone say) haha.... and I'm not asking this because I'm dumb. I'm quite a nerd when it comes to technical things. However as simple as it may seem, I want to make sure I get the connections
Read more…Hi all
how to use arducopter for auto photo?
I need to make a quaid for automatically make shots at each waypoint (or every 20 meters of track).
I configured shutter as specified in the manual and checked - from input 7 shutter work. shutter on channel
Is it possible to add a speaker to the quad that noises when the battery goes low. I have the 3dr battery voltage monitor but having to hook up the laptop is a pain
Read more…I have got a 3DR Hex and APM 2.5 by default the loiter radius is 5m can this be reduced ,is it a good and I so how low can it go
David Ardis
Read more…I sent another post of the same message, but I messed up sending it to one individual. Sorry for the mistake.
My question is during the last two times I waited until the failsafe alarm went off to land my hexacopter. Although, when the alarm went of
Read more…Hello,
IWhen runing the motors of my quad, I hear (seems more at low speed than high speed) some short clicking sounds. Seems to come from the motors.
Does anynoe knows what this is ?
Thx,
Read more…Hello,
I have this kind of curves on a few minutes of flight with 3DR radio telemetry, at short distance (thus not caused by long distances). Seems to be increasing radio rx errors. What does this mean ? Do I have an issue with a cable ? or antenna pr
Read more…there is a check-box just to the right of the calibration button on the mission planner.
What is this for / i don't see any documentation for this?
thanks
Damo
Read more…hi,
i have just built my arducopter. it is calibrated, the esc's are calibrated.
When i take off it move in the direction forward and right.
i have tried re-calibrating again to no avail.
Any ideas as to how i can debug this?
thanks
Read more…This is a diy project I started based on information assembled from different places. Some inspiration comes from a guy who posted a blog about a FPV suitcase for less than 160$, i reused some of his ideas. I would like now to share this in the
Read more…Hi,
I use the modded T9X with ER9X firmware.
Until now I had it simply programmed and configured to use the 4 channels for yaw, roll, tilt, throttle and the fifth channel for 6-mode selection.
I find it very sensitive at around 50% throttle to find the
Read more…hi,
i am building my arducopter.
I have it on the same flat surface that it was calibrated on.
I have calibrated the ESC's
I have calibrated the quad.
It do not have the props on yet. I already have a quad (x650) that flies fine.
When i give the arducopter
Read more…Hello All,
In arduplane you can set RST_MISSION on a pwm value allowing you to reset the mission in flight, can this be done in arducopter? as there is no rst_mission in advanced parameters.
regards
Read more…