Hi All:
For example, I want to swap the output of ch4 and ch7 so that I can use ch7 as ch4 and leave ch4 unused currently. Is that possible?
Thank you in advance
Yucong
Read more…I found one of my motors is always beeping ( the one connected to ch4 output, I did ESC and radio input calibration).
Then I measure the voltage of ch4 and chs 1,2,3 with transmitter off.
I found the voltage of ch4 is 1.7 volt lower than ch1,2,3. Is th
Read more…Newbie Question - Please Help
During my initial setup, arming sequence was throttle stick to bottom right corner. Now all of a sudden the arming sequence is done by going to top right corner and dis-arming is top left corner.
What did I do wrong and ho
Read more…Sorry if this question is "out there" but I was wondering of the ArduCopter pilot and IMU could be adapted without too much fuss to work with an underwater ROV.
The ROV in question is essentially an "upside down" copter with one thruster pushing the
Read more…Hello,
I am incredibly new to the ArduCopter scene (in fact I only built my 3D quad yesterday and am still waiting for the liPo and Tx/Rx controller to arrive) and would like to mount a small compact camera to my ArduCopter. Can anyone tell me whether
Read more…I noticed that when I cut the throttle the motors stop very quickly. And when the propellers are still (while power is on) and I hit them with the finger they does not spin any turns (like when power is off).
This leads me to think the ESC has breakin
Read more…I have an ArduMega 2560 with GPS and Compass to install on a Quad frame. I would like to be able to fly this indoors and outdoors.
Is the GPs required for the system initialize or fly stabilized?
Can it be disbled via a switch?
Thanks,
Read more…I looked around in the wikis and forums but I could not find updated info on this matter.
Can somebody please help me to sort out the use of parameters Throttle Rate and Altitude Hold?
I also wonder about Acro Roll and Acro Pitch - are they at all used
Read more…I have had my ardu system for a couple months, I have it all soldered together with the GPS,
Xbee down link, Sonar sensor, air speed sensor.
I have been flying the DJI WooKong system on the Fyetech.com Y6 and the multiwiicopter.com scarab
with great r
Read more…I got such datalog display in the mission planner, which is wired. I tried to display the highlighted column but only two long and strong bees came from my laptop. I used 2.49 firmware and 0.87 ground station. The log data is of tlog format. I could
Hi All:
I am able to connect the arducopter and groundstation with xbee telemetry. But when I put the switch in CLI mode and use terminal of groundstation. I says " error reading com port" and sth else.
Did anyone come across similar situation? T
Read more…How would you know that your IMU is busted? We sometimes have a wrong readings for the attitude of the helicopter. Do we have a software to test if the IMU has a problem?
Read more…I DL'd the Mission Planner and ran ArdupilotMegaPlanner.exe. But I just get a blank MVS 2005 screen! What have I done wrong?
Monroe
Read more…hi，I am fresh. Now, i was researching the copter with four fans. However , i was confused about the problems, like" how many size of the fans and speed of the motor for loading the copers? so, if anyone know how to solve the problems. could you
Hi All:
I am the newbie and here again.
This time I have an Xbee connection failure.
I use xbee pro 900 wire antenna and an adafruit adapter board on the arducopter side, along with an xbee Pro 900 RPSMA. I setup the Xbee modules according to
Read more…Hi All:
I am a newbie and building my first arducopter.
I connected receiver to the APM and the APM to the power distribution board as in the wiki.
No matter how I move the transmitter's stick, there is no response from the motors. There are
Read more…Hi guys,
I am struggling with my first ArduCopter hexa project and right now I feel a litte down-hearted about my progress (lack of).
I have been able to fly it decently in Stabilize mode, but it´s oscillating in roll axis so there is definitely some
Read more…This is a copy from a Ground Stations thread where a user reporded unable to enter anything into the parameter fields in the battery tab.
- I experience exactly the same problem!
Though I am currently using Mission Planner 1.0.82 and APM fw 2.0.49.
I ca
Read more…Hi Everyone:
I am a newbie. I am using a turnigy 9x transmitter and receiver.
I tried to set up my radio of my arducopter. I came to radio input of APM setup. I moved my rc sticks but found:
when I moved the stick assigned to roll. The yel
Read more…Hi all,
I'm starting with my quadcopter project and yesterday i had my first fly without crashing :)
Now I’m trying to install an AttoPilot sensor to measure both current and voltage following the instructions in the page:
http://code.google.com/p/ardup
Read more…