We really don't know what the problem is (because we just followed the setup for our heli) but everytime we reset the apm+imu, the set up requires us to set the radio frequency, or pids, or the levels, or the declination values.
Is there a way to ret
Read more…Hi
I have a 3s 4000mAh and a 4s 5000mAh Lipo battery and would like to try out how the flight time changes; but can I just swap the battery or do I have to recalibrate the four ESCs of my quadcopter to work with the other battery?
thanks a lot
Felix
Read more…
the output 3 isn't working so i need to reprogram the outputs please help
Read more…We are currently testing the connection of the GCS and the Heli but we can't connect thru xbee communication. We could have the data and programming using the usb. Can anyone tell us whats wrong? We are using the xbee module suggested in the site of
Read more…I got the ardupilot + oilpan w/ gps, stuck it on my own frame with 750KV motors, along with hobbyking's 18-20A ESCs. I got everything running, but the flight was a disaster.
I was thinking in getting a frame I know has been flown before, the question
Read more…Hello everyone, I e been testing with my quad FW 2.038, and set all PID and seems to fly well, but noticed that the throttle and is way too sensitive, down or up the quad very fast with a small stick movement. where I can adjust the sensitivity of th
Read more…Hi Guys
I have a bit of an issue with my copter. If anyone can give me some advice, I would be very grateful.
I am carrying a payload of about 750gram. This includes a GoPro, AV transmitter and bat pack, Xbee and landing gear. When I fly, the copter
Read more…Hi
Can some kind person on the forum help a total newbee with the right cable plugin for a hexacopter config. I am using a seven channel futaba 6EX and R617FS receiver and need to know which cables should i attach from the receiver to the Board to ge
Read more…Well... needless to day, my ArduCopter is becoming a bit of an obsession..... Here's a video of a few of the highlights from my first flights!!
Since then I've crashed a few times trying new things and made some modifications..... I've been working o
Read more…Hi,I was trying to get my head around the code in arducopter 2.0.36 to see if I could set up an IF condition to detect if the attitude read from the IMU shows that the quad is inverted and then turn on the relay, which in turn ejects a parachute from
Read more…I wish to add a pan/tilt/roll camera on a octa
it is possible do assign channel 9 (pan) in PL3 pin?
Read more…Hello everybody. I've noticed some of you have some doubts on wich frequencies of radio are usable within your country. I've found this table very usefull when in doubt. http://www.futabarc.com/faq/frequency-international.html
Read more…With so many choices in diydrones store it's hard to know which one use. I want to purchase one for my quad and one for my y6, but have no idea if there are differences that I need to be aware of.Are there Pros/cons to the different models?
Read more…Hi Guys
I have recently started with my Ardu Copter. The build is complete, the setup with my radio (Spekrum DX7) is done (on fixed wing mode), my ESC's are calibrated. No connection problems and all seems ready to go. On doing the initial hand test
Read more…I am trying to figure out the possibilities of ArduCopter as an autonomous microUAV research platform. Right now we are going to acquire a quadrotor to start working on it. I am having some difficulties in knowing which are the actual performances of
Read more…Hi,
I just bought an ArduCopter Kit a few weeks ago and finally assembled it. Now I have some issues communicating with the board via the APM Planner.
Here is a bit of history of my problem:
1. I was able to connect, download and configure the software
Read more…Been testing Simple mode in our indoor arena.
I assumed that it will take the position and heading when you switched on the quad as "home"
I fly around, and then enter alt_Hold in front of me with the Quad facing "tail in".
When I switch to simple mod
Read more…While setting up the Quads for my customers, I often wonder about the following (Jason, I think this my be yours).. ;-)
1. When you look at the dials in the planner, the heading is shown. Is that Heading supposed to be magnetic, or true north based?
Read more…Hi Chris,
This is not a moan, just some small things I would like to see in the next batches of quads to make an excellent product even better.
1. In the first batch I received from JDrones, all but one of the kits had bullet connectors soldered on
Read more…Hi,
in case no one signalized this yet here and Jani or other AC makers wouldn't know: many people seem to be having problems with the ESC to motor connectors supplied with the jDrones ArduCopter Kit (checj here or here). I crashed my AC about 4 times
Read more…