Hi to all,
I would like to be sure how the land function is working.
On the documentation, it say that it is using Alt hold function.
But if I try to switch from Stabilize to LAND, with wind, my quad is landing on the same vertical, like a loiter.
Then,
Read more…Hi folks,
I've just noticed that the logs / tuning graph shows RC 6/7/8 having output even though there is no actual output. Once I press the safety switch then the outputs really do spring to life.
I have channel 6/7/8/9 set to rcPassThru (1) and watc
Read more…Trying to make something a little more compact than my last design-still haven't had that one in the air-snow and cold!! Anyway I have a 550mm octo with 240mm plates turning 12" props. Working on getting the pixhawk setup now. Bought a 3d printer so
Read more…I am running MP on a win10 tablet, and when I select an alpha numeric field to edit, the keypad interface does not come up, so I cannot edit the field. This does work right in any other program on the tablet. Is there a tablet mode in MP that I haven
Read more…Have fairly light weight and powerfull 410mm quad running oneshot ESCs. I get a Choppy throttle response in alt hold, throw altitude holds ok. I'v set the Loiter and throttle accl pids as low as mission planner will allow: Loiter alt P:1 and throttle
Read more…I'm in the process of building a FireFly sport with Pixhawk PX4, I'm using a Futaba T14SG with R7008SB RX. Also going to using a mini OSD for small Screen on TX. I'm looking for any details on base setting for theThanks in advanceLarrylarryhalliday@i
Read more…It seems impossible to set the power monitor.
No matter which options i use, it is impossible to save the Amperage reading.
Without this it is impossible to do the motor to compass calibration.
This problem is happening both for Clone Pixhawk as well as
Read more…Hello to All,
I need help from you all to figure out why my APM based copters are having unstable altitude hold (in all mode that used barometer). I am having the exact same problem on my APM based tricopter, as well as CX20. Both have the APM2.5 cont
Read more…Hello to everybody
I m building a hexa copter with pixhawk
I have upload the 3.3.2 and the mission planner is at 1.3.35 and i cant find at the drop down menu at channel 7 or channel 8 the landing gear option
I have attach a picture of my problem
hello,
is there no DIY for Sabretooth Motor drivers to be controlled with APM 2.5 using RC??
Read more…Hey,
I want to forward the parsed telemetry data (such as roll pitch yaw and altitude) from a ground control station over a UDP or UART port so that I can receive it in another software on the same PC. Is there a way to do this? Which GCS do I need? (
Read more…hello friends,
i have built a 4 wheel driver Rover using a Aurdino Uno board with a L298D Dual H Bridge Motor Driver.
i wish to replace the Aurdino Uno Board with an APM 2.5 board but now I don't know how to interface the L298D Dual H Bridge Motor Driv
Read more…As most of you, I can create my own terrain data from a flight with my UAS and computer vision software. I would like to use that data to fly my UAS at a constant height (distance) above the ground level in Mission Planner... say I want to fly at 10
Read more…For all new Mission Planner users running Windows 10 on their computer and finding difficulties installing all drivers, I have included instructions on showing you how to get this to work.
1. The first the you will need to do is disable your Driver Si
Read more…Hello all ,
I just get Digi 9xTend 900 Mhz and I want to connect it to my pixhack ( chines pixhawk )
I can't configure the 9xTend and connect it to the XCTU software using TTL ,
the pin out of the 9xTend is :
pin 1= GND
pin 2 = VCC
pin 3 = GP02/RX LED
pin 4
Read more…I have been working on this setup for a while now. It's finally working.
The heart to it is the custom code I wrote for the ESP8266 to serve as a UART - TCP client that connects to a server in the internet. The GCS connects to the same server. The ser
Hi guys,
I've been searching the last few days for schematics or CAD files for the now discontinued frames from 3DR (Quad/X8 specifically) without any luck. Almost every promising link leads to a dead site due to rehosting/migrating of info.
I was wond
Read more…All,
Before I go out and buy a brushless gimbal that I'm stuck with and is incompatible I'm wondering if people out there have a working configuration already.
I've got a Raspberry Pi camera which weighs in at single digit grams, so it doesn't have to
Read more…Hey there,
I have a few problems involving recording flight data with the dataflash logs:
Problem 1:
I recently tried to change the type of information that was stored on the dataflash logs on board my Pixhawk, and to change this I went to the parameter
Read more…Having recently gone through RPAS training with a so called "school" which basically followed parts of the Private Pilot's License curriculum and taught almost nothing about the RPAS flying or industry, I wondered what would be the best way to teach
Read more…