I want to power the input side of my APM 2.5 with 10A bec. I also want to use a 90A Attopilot to monitor current and voltage.
I have it set up very similar to my APM 2.0 and have used the same pins as for APM 2.0, A1 A2 for the voltage current.
I have
Read more…Before trying the Auto mode for the first time, I want to make sure I know this detail :-)
Are all the values in meters or is the application taking the windows defaults, example in US feet and the rest of the world in meters?
Read more…I'll just be direct here, so as not to be overly long.
The 2.9.1 forum thread is past 1600 posts, and I have no doubt it will hit 2000 posts shortly.
The problem with that thread is that it's crushing under it's own weight. The same or closely relate
Read more…Hi, Is there something that should be tuned/changes after upgrading as mentioned in subject ?
Especially during level flight, huge, rapid changes in RPM can be heard.
Read more…Hey all, I recently had a crash with my S800. Here are the details: Copter was about 25 feet away from pilot, 10 feet in the air.
Locked-up, descended quickly in an auto-land on hard large gravel, props did not seize or stop rotating.
Copter did not r
Hi Guys,
I do not know how many have had issues with 3DR/ udrones customer service. I am quite disappointed with their customer service response:
1. I do not see any customer service number to call/ enquire. I am surprised!!
2. Not completely informativ
Read more…What would it take to get an item added to the Mission Planner Speak items?
I use my laptop as my base station and I've turned on speech and I find it very handy.
I had problems sometimes hearing what was said, so I added a bluetooth head piece. The b
Read more…It is not clear what is the functionality included on the std arducopter code for apm2, and how to use the different led outputs available .
Could somebody clarify please ? It seams to me that some functionality has already been included on the firmw
On the wiki I did find next affirmation below.
Where is located on the APM layout the compass?
What exactly need to be checked as secure solder?
"My copter suddenly crashed for no good reason: The I2C port, used to talk to the compass, has a rare but ve
Read more…Is it possible to use 3D power module with APM 2.0. If so, how to make the connections??
Zafer
Read more…Hi Guys,
Has someone tried (in code) modifying/descaling the loop time and running the arducopter? Currently, it is 50Hz (20ms) for each loop to trigger the motors.
Has anyone tried decreasing the loop frequency/ increasing loop time for saving time o
Read more…Today I flew at a different site which had stronger wind than I have experienced before.
I had been flying 2.9.1 release for the last few days with out any problems. The flight today was going well I selected RTL the quad climbed to 15 meters and tu
Read more…hi everybody ......
my problem is that minimosd works fine by itsself but when the 3dr radio fitted ,3dr radio works as it should and osd shows all characters. BUT the characters dont change all stay at zero as if the apm inform isnt going into the
Read more…Just so I could have the actual binary that gets downloaded by Mission Planner, I would like to have the Arduplane 2.6.8 Firmware - not the source. Any place to get it?
Read more…I took my antenna tracker hardware out to the field today with the goal of flying around and confirming that it would follow the airplane around.
The tracker is Maestro-based and is responding correctly to both the Pololu config program and to the tri
Read more…Lets all stick together please sign this petition..
Lets nip this in the bud before it spreads...
LINKS:
http://roswellflighttestcrew.type
Read more…Hi @Chris,
I am not sure if someone has asked already this question on forum before. The APM 2.5 has accelerometer, gyros, magnetometer, barometric pressure sensors.
Apart from this I wanted to use 4 IR sensors, 1 sonar and optimal flow sensors (which
Read more…
Runs on android and there are already few GCS for android...
Read more…Having finished the camera Gimball I'm very happy with it apart from the control I've got over the servos from the APM2.0
The movements seem very coarse and slow. If I tilt the machine quickly the gimball lags behind but does go level. I've tried diff
Read more…I am trying to make airborne my quad X, but it flips always. APM2.0, quad X, 1000kv, 30A ESC.
I did re-calibrate Radio, ESC, balanced motors and props, check the CLI motors order and rotation. All those steps looks fine, but quad still flip.
I decide
