is there a way to get the current drawn by a gimbal motor in full operation?
motor specs:
Poles: 12N14P
KV(RPM/V): 210
Resistance: 10.4omh
Weight: 35g
Wire: 0.19mm
Torque: 240g
camera weight: 135g
I was wondering this because my gimbal controller can ha
Read more…Hi,
I`m having a high Z vibration as shown in the Mission Planner vibe panel. The octorotor (a X8+) is flying fine.
I would like to know what exactly means a high vibration in the Z axis? Its related to the roll, pitch or yaw? Or is more like thrust is
Read more…Hello can anyone help just setting up my Hex with F/W 3.2.1 and I noticed this difference in outputs to the motors, the screenshots were without props on a flat surface.
Am I just worried about nothing or is there a tuning issue?
Read more…Hello all,
I can not calibrate my internal compass anymore. No problem for the external but the internal doesn't show any sign of life.
As you can see in the image below the second compass during calibration doesn't move.
Do you have any advice on this
Read more…Hello,
I am new to Mission Panner python scripting and my goal is to write gps coordinate to a file using python scripting.
import os
import os.path
import subprocess
home = open(‘C:\\data\\mycoordinate.txt', 'w')
print os.getcwd()
When I run i
Hello, I am new to Mission Panner python scripting and my goal is to write gps coordinate to a file using python scripting. import os import os.path import subprocess home = open(‘C:\\data\\mycoordinate.txt', 'w') print os.getcwd() When I run it in M
Read more…Hello,
I am new to programing python in mission planner. I am trying to run a basic script where I need to save GPS location to a file. So This is example how I want to write to file in python script. But when I load and run the script in Mission P
Read more…Hello,
I am new to Mission Panner python scripting and my goal is to write gps coordinate to a file using python scripting.
import os
import os.path
import subprocess
home = open(‘C:\\data\\mycoordinate.txt', 'w')
print os.getcwd()
When I run it in Mission
Hello,
I am new to programing python in mission planner. I am trying to run a basic script where I need to save GPS location to a file. So This is example how I want to write to file in python script. But when I load and run the script in Mission P
Read more…Hello,
I was just wondering, how much current can a 14 AWG wire handle?
can anyone explain and give further detais on this matter?
Marco
Read more…hello everybody
I confused about quad-copter model identification , since the quad is unstable in open loop ,then how can I identify it since is unstable ??? but if I add a controllers in loop of system and re-identify the new global system in close
Read more…Im having trouble with getting the my quadcopter in loiter to keep its position. It seems like its loosing the signal, but my gcs says the GpsHDOP is at .8 and there are at least 10 sats. it will hold for a few minutes then suddenly takes off in a
Read more…hi All
i add new functions for onboard display (now supported for linux version board)
it may to be used for pixhawk and other controllers too
ssd1306 it is small and low cost display (~4 USD)
data connection and powering from i2c port
it may to be inter
Read more…Mission Planner 1.3.41
APM:Copter 3.4rc5 Quad
Does anyone know if there is a way to create a mission which will switch between terrain following and relative altitude mode? I'd like to be in terrain following mode for part of the mission while the cop
Read more…Hello all,
can a single ubec like this http://www.hobbyking.com/hobbyking/store/uh_viewitem.asp?idproduct=31702 provide the 5 V. to power up a camera and at the same time being a powering backup for pixhawk?
Regards.
Marco
Read more…Hi everyone,
Any idea why my quadcopter fails to hover, there are a few things i noticed. Only my throttle works the pitch roll yaw does not work. Im using the X frame and i followed the apm motor numbering in the output but nothing changes even thou
Read more…hello to all, yesterday(like typed in the thread before) i burned out my apm 2.6. I checked inside case and i find the smd diode burned, so i replaced with a little wire.
The fuse looks good and i can mesure 5.2 V between gnd and fuse.
Now the apm, wh
After my quad got stolen, I started to think if it's possible to implement any sort of software or hardware protection like password lock or something. Do you think it is possible to implement?What I have in mind is a configurable set of values on al
Read more…I want to update esc in one copter that have old common ones but this stuff updates so fast that I find new ones every time when I open HKing page, many of them specialized to racers now, like this one: http://www.hobbyking.com/hobbyking/store/__1077
Read more…Running an APM mini 3.1 with the stable release 3.2 firmware.
I had a series of events leading to this investigation. I performed an auto land with a 550 class drone. 15" CF props and 30a generic SimonK ESC's. The auto land went pretty well and settl
