i lost my airplane and all the equipment on it because of bad compass health error and i don't no way its happen .
as you can see in video after i takeoff and get some distant i engage the RTL and it want back and circle ab
Read more…I am building my new Tarot 650 and have started experimenting with FPV which I bought from 3DR. I power my FPV camera and transmitter directly from my 3S battery. The image is transmitted correctly but as soon as I start the motors the receiver monit
Read more…Hello Pilots,
So I'm building my first quad copter, I only have experience with fpv planes at the moment.
Quad Components
Atmega 328, Hobby king flight controller V3
BEC 12A Hobbyking ESC
Turnigy Mini quad frame
FRSKY DJR-II plus, Receiver and Transmitter
Read more…Hi everyone,
I am trying to get real time sensor data mounted on my drone. I am using a Pixhawk as the flight controller and MAVLink for radio connection. I need to get the sensor data via Mavlink, process the data and feed it into another program.
Read more…
Hello there everyone, hope I'm posting this in the right spot..
A friend of mine has a business and he wants me to help him make a land vehicle (is rover the proper term?) that can carry a small camera that takes 360 degree photos and videos.
This vehi
Read more…If to fly at low roll and pitch degrees, the GPS always looking to the sky very good. But when the airplane going for example to the 90 degree roll, then the GPS position now is at the horisont but not at the sky so the data I presume will be very in
Read more…Hi everyone.
I had solve the previous problem with the help of the forum user Mr Steve Foster. Now I have another problem with my FPV live view. Please check the attach video file. The monitor is from 3Dr and the channel was at Div band B and channel
Read more…Hi all,
I have a custom quadcopter frame that is controlled by a Pixhawk. While testing the frame in auto flight, I have observed extensive pitch oscillations when the quad is in horizontal motion while descending as shown in the descent phase of the
Read more…I found the file: cameras.xml in the MP folders, but is there any documentation anywhere describing how to actually add a camera? Or do you just cut/paste the XML and figure out the fov, image sizing, etc?
Thanks
Hi all,
I have FX-69 FPV eqiupped flying wing with APM2 (3.3.0)+NEO-7M.
Recently I flown to my first 1km heigh and got some troubles switching to RTL mode.
My RTL heigh is set to 100m and i flown a lot of times with no problems, but that day I was going
Read more…Hi
I need some input for solving a "problem" with flying a multirotor in a tube (dont ask why ;-) )
When flying manually in a tube/pipe with relatively short distance from propellars til the tube-wall there seems to be a vacuum spot in the center of th
Read more…Hi Guys, working with mavproxy I can use the command "arm throttle" to start the drone's motors.
Which command can I use to do the same thing with mavlink?
Please, can someone show a simple example?
Thanks
Read more…Greeetings to everyone ..
i am about to continue my Father Company which is Photoshop in the pass since 1992yrs.. but when that time we are use helicopter to fly and take aerial View for Large Company for building process
as technology changes now th
Read more…hi.
i use APM 2.6 Arduplan i have problem in modes before flying mode manual is work but after swiching mode to Auto throttle is immediately cut down,i need solution for these problem please...
Read more…Hi,
I am a computer science student (KU Leuven - Belgium), specialization secure software.
For my thesis, I will perform a security analysis of the software/firmware running on drones. After a lot of reading, I have found that there has been a lot of
Hi Guys,
I'm trying to set the computer out using Pymavlink, but I don't know how can I do this.
Using following command on Mavproxy it works fine:
mavproxy.py --master=/dev/ttyACM0 --baudrate 115200 --out=192.168.1.10:14550 --aircraft MyCopter --consol
Read more…Article: http://fortune.com/2015/10/21/government-public-drone-registration/
Link to submit your comments: http://www.regulations.gov/#!docketDetail;D=FAA-2015-4378
More discussion:
https://www.reddit.com/r/Multicopter/comments/3prtrr/the_dot_is_asking
I would like to lower the loiter down speed. I can't find where this can be done. I am running 3.2.1 firmware. It used to be done with WP_NAV_DOWN apparently this will only work during a mission now. Is there an adjustment?
Thank you for any help.
Read more…Hi all, I have just "UPGRADED" all my multies from the Dji A2 to the Pixhawk.
What a difference, Arducopter rules the sky.
I am having trouble finding info on gimbal capabilities with Arducopter. I note there is options to set the serial to Alex Moss
Read more…