Hi,
I have an initial mission that consists of:
1.) Takeoff
2.) Waypoint
3.) Condition Yaw
4.) Loiter Unlimited at the Waypoint
After the mission is on step #4 or even while the Mission is executing, I would like to update the Yaw angle and the altitude of
Read more…I have 4 quads.
1. A micro 220. Currently on the shelf, 'cos I broke a prop, and the spare.
2. A commercial prototype. Grounded for CoG and vibration issues. Cause still not discovered.
3. A TBS Disco. Grounded, because an ESC has a loose connection, an
Read more…Hi guys,
Doing a fun project to make the fastest quad I can. I am planning a very small (330 size), light (circa 1kg with FPV + APM2.5 + GPS) quad, with no requirement for long flight times or payloads, although 5 minutes is the minimum. It's all ab
Read more…I've started seeing a problem with my copter, where the OSD will initially work, but once I take off, it will repeatedly flash 'requesting datastreams' and then reconnect and work for anywhere between 5 and 30 seconds, before repeating. It never does
Read more…Anyone have a pinout diagram for the Samsung NX1000 USB pinout in order to get video out? I have tried HDMI output however the camera only shows the playback function and not video when using HDMI.
Any help would be greatly appreciated!
-Oliver
Read more…So, I have to assume there's some code that takes this into account, but I have a problem with the Barometer. I have an SK450 with an APM 2.5+ with 3.0.1. When I'm in alt hold and the copter is not moving, I have no problem with holding altitude, but
Read more…Was flying my 800mm quad yesterday, flys well have not had any previous problems. I ran Auto-tune yesterday. It took a good while to run thru the roll portion of the test. Shortly after it began the pitch portion of the test the quad just abruptly st
Read more…Can any one direct me to this information...telemetry values and definitions. I have looked high and low with no success. I hope I'm in the correct "Discussion".
Thanks, Brian
Read more…Hello, i've ordered a Pixhawk from my local reseller.
Now i need a little help, because i'm really uncertain concerning the appropriate sensors.
For gpssignal, i've ordered a uBlox LEA-6H Modul without compass and for my 9x a 8ch ppm encoder. Is this
Would this WP set up work to have the plane fly a repeating pattern until I tell it to stop? See pic below.
Hi,
I have a problem with my simulation, because when I try to load a 2.68 or the last Plane HIL firmware to my PX4 with Mission Planner, appears the attached page
Ideas?
I have not one
Thanks
Martin
Hi i just read a new intervalometer developed by CHDK geeks specifically for uav and kap photography.
Unlike other scripts for UAV photography like the one of conservation drones, Dronemapper, Event38, etc. With this script you can set a range of valu
Read more…Hey guys,
I was using Droid Planner for outdoor navigation, perhaps we could have a feature incorporated to use it indoors for navigation?
Read more…Hey all,
I'm wondering what you all think the design of this new APM powered TriCopter: http://VisionAerial.com/SwitchBlade
~Thanks in Advance.
Read more…Hey,
So i have calibrated my ESC's however i don't get 4 tones for my 4s battery only 2.. I have followed APMcopters ESC calibration instructions, both individually and all at once. When i do the all at once method after raising the throttle and disco
Read more…Hello,
I'm trying to avoid an issue with the 5v regulator on the analog side (12v input) . It drastically decreases my UHF radio range by creating noise in the same freq (433 MHz)
From the wiki, i see this option to connect the analog/digital sides so
Read more…I have been flying a BIXLER 2 this summer with APM 2.5 , 3DR GPS LEA-6 , 3DR Telemetry , 2.74 software. I have probably had the most fun in all of my 50 years of model flying. I am now auto taking off ( hand launch ) flying 30 waypoints in 12 minutes
Read more…Hello everybody,
I have the following question on the PM message of the Dataflash.
This page (http://copter.ardupilot.com/wiki/downloading-and-analyzing-data-logs-in-mission-planner/) describes each field of the PM message of the Dataflash.
However, in
Read more…Hi all,I'm using mission planner and have just connected the joystick. It's cool to see the joystick move the control surfaces of the plane! But is there a way to use the joystick in non-manual modes such as FBWA to have the benefits of stability?
Read more…I was wondering if there are any new solutions on sending the display from a Sony NEX to a ground monitor. I have read some older posts that suggest a micro HDMI --> analog converter but I have only been able to find on eBay the ones that convert an
Read more…