Hi
I am using Arducopter-2 with APM-1
When i went for a test flight, everything seemed ok at startup, but after i powered the motors, the angles/gyro rates/mag started giving erratic readings even when it was stationary on the ground.
Attached is a scre
Read more…Hi all,
I've seen a few Android projects around using bluetooth bridges, but I was wondering if anyone had thought about connecting a 3DR radio to an IOIO board (IOIO board contains a single MCU that acts as a USB host and interprets commands from an
Read more…Hello, new member. I have searched the site a lot about this without any luck. I'm using apm2 in a Great Planes Stick 60 airplane. The software version is very recent, no more than a week or so old ( you can assume early July 2012 version on everythi
Read more…I can’t figure out what firmware to load as that configuration is not listed in the Mission Planner? http://code.google.com/p/arducopter/wiki/APM2_Motor_orderThis is the coaxial 8 motor not the flat 8..
Read more…Hi folks,
I maidened my APM2 yesterday. It's running the latest code offered by the mission planner--2.34. I've got the skywalker parameters file from april 2012 set on it.
Just as the subject line says, when I switched to either fbw A or stabilize
Read more…Hi..i try to change my flight mode to "Auto" for auto takeoff but nothing happened. When i check using telemetry i noticed that the flight mode does not change even after the "Auto" mode is triggered using CH5. It still show "Stabilize". I tried repr
Read more…I like to know what do exactly reset button? I only know is that when something is wrong I press the button and sometimes fix problems.
Thanks
Hi all,
Does anyone know why when I download logs using Planner 1.1.96 from my APM2 running the 2.6 code, I sometimes get a .tlog along with the .log, and sometimes do not?
Thanks,
Aaron
Read more…I am wondering how the APM2 will react on a twins motors airplane, when one motor is down (completely or partially).
Will the rudder and ailerons trying to compensate this and keep the plane on stabilized mode? Will Auto mode also work?
Read more…In using the Mission Planner (Ver 10) to upload the A/C specific configuration (easystar.param).via the AMP a dialogue window opens with the title "SAVED NOTE" with the message "4:22:48 PM Easy Star Post Crash"
The OFP (firmware) loads ok with the gen
Read more…My APM2 was dropped off by Mr FedEx today. I've read through the wiki and have noticed a few people saying it's vague in places. So before I get home tonight and start poking around, is there anything anyone feels should be added to the quick start g
Read more…I have just parked in front of the Museum of Science and Industry and on the last few miles of my voyage to get here, I couldnt help but see tons of garbage all over the place. Just littering the grass and parks / streets.The drones.... Finish this t
Read more…Hello Everyone,
i actually continue to have serious issues getting APM to work in e.g. Loiter.
Here, you can see a video with the usual behaviour: http://youtu.be/3HDaQzrht9w
Out of 20 times i tried, loiter worked two times. - In between one time it wor
Read more…Hi guys,
I'm new to this and just started powering my board. I'm having issues powering my servos from the PWM input side. I have set the jumper correctly and still doesn't work. I have tried powering from the PWM output pin and it works fine. I would
Read more…Hi Guys,
I was trying to setup a Logitech Attack3 joystick for manual control of my APM running the latest ArduPlane 2.4 firmware.
I'd like to mention that I have NO R/C system connected to the APM (I don't even own one). Perhaps this is the problem. I
Read more…I have a strange problem with my APM1 2560.
If I load the arducopter code the compass works completely as expected.
If I load arduplane 2.40 code on the same APM then the compass keeps coming up disabled.
I can set it to enabled but when I next connect
Read more…Hi,
I've got a few spare 5V 328 Arduino Nano's floating about and a couple of LCD panels. I was wondering how hard it would be to take my XBee radio, hook it up to it and decode the Mavlink 1.0 binary protocol? Is there a library I can add to the Ar
Read more…Hey guys
Just got the APM 2 for my quad so Im putting my APM 1 into my bixler. I cant seem to find the Config files for the bixler.
Can anyone help me out here?
Thanks
Read more…Hey guys (mainly 3DR, but anyone who has input/suggestions)
I have quite a few APMs and three APM2. I've got one that I haven't flown (an APM2) and I just put a case on one of them... I believe, in fact, that I've hadn't yet flashed this one, as it d
Read more…I just lost my Skywalker 2 days ago. It had GoPro, etc on it.. lots of money and time. I don't have my APM2 yet and I had no RTL . Still not sure what happened to it, as the video just went completely off, no warning, did not flicker, never came b
Read more…