Hello Everyone,
i actually continue to have serious issues getting APM to work in e.g. Loiter.
Here, you can see a video with the usual behaviour: http://youtu.be/3HDaQzrht9w
Out of 20 times i tried, loiter worked two times. - In between one time it wor
Read more…Hi guys,
I'm new to this and just started powering my board. I'm having issues powering my servos from the PWM input side. I have set the jumper correctly and still doesn't work. I have tried powering from the PWM output pin and it works fine. I would
Read more…Hi Guys,
I was trying to setup a Logitech Attack3 joystick for manual control of my APM running the latest ArduPlane 2.4 firmware.
I'd like to mention that I have NO R/C system connected to the APM (I don't even own one). Perhaps this is the problem. I
Read more…I have a strange problem with my APM1 2560.
If I load the arducopter code the compass works completely as expected.
If I load arduplane 2.40 code on the same APM then the compass keeps coming up disabled.
I can set it to enabled but when I next connect
Read more…Hi,
I've got a few spare 5V 328 Arduino Nano's floating about and a couple of LCD panels. I was wondering how hard it would be to take my XBee radio, hook it up to it and decode the Mavlink 1.0 binary protocol? Is there a library I can add to the Ar
Read more…Hey guys
Just got the APM 2 for my quad so Im putting my APM 1 into my bixler. I cant seem to find the Config files for the bixler.
Can anyone help me out here?
Thanks
Read more…Hey guys (mainly 3DR, but anyone who has input/suggestions)
I have quite a few APMs and three APM2. I've got one that I haven't flown (an APM2) and I just put a case on one of them... I believe, in fact, that I've hadn't yet flashed this one, as it d
Read more…I just lost my Skywalker 2 days ago. It had GoPro, etc on it.. lots of money and time. I don't have my APM2 yet and I had no RTL . Still not sure what happened to it, as the video just went completely off, no warning, did not flicker, never came b
Read more…Hi,
Yesterday, I tried out my Arduccopter for the first time in a few months.
The newest software (2.6) was on the APM1.
I was getting delighted to see that all the occasional motor starts had gone that used to happen when "connecting" MAVLink etc. Befo
Read more…'m having some trouble adapting the new IMU v3 to Jean-Louis' code written for tricopters. His code used the APM_Compass library and for some reason, it wont compile with any reference to that library. The new IMU doesnt use that library, so I have
Read more…The altitude on the HUD and other places is off by a factor of 10. (too little)
Version 1.1.96
Earl
Read more…I decided to purchase the Xpro Heli Camera Mount 2 to add to my SK-450 quadcopter platform.
When I opened the box I was impressed with the craftsmanship, but skeptical about the tinsel strenght of the 1/8" aluminum landing gear. I figured it MUST b
Read more…I am in the process of converting from MAVLink 0.9 to MAVLink 1.0. I use a bit stream processing method for decomming (parsing) the MAVLink frames. I define each message that I am interested in as a spread sheet (see attached). I derived the spre
Read more…Recently purchased a QuadCopter from uDrones and been having fun putting it together and getting things to work. uDrones has been very helpful in answering all my silly and stupid questions and I'm grateful for the support. Just before the 4th of J
Read more…Hi,
does anyone have experiance with the AC2830HE-508 motors ?
I want to upgradw my current hexa, and was wondering how are thay compared to tiger motors or the avroto motors in much the same price range ?
Read more…
After I upgraded the missionplanner I can't see any advanced params. I've got .Net 4.5 installed and it has worked before with version 1.1.94 for example.
I am interested in the MinimOSD but I am using Arducopter 2.6 which upgraded MavLink from 0.9 to 1.0.
Since the Minim OSD uses MavLink I would like to know if it is compatible with an ArduPilot Mega 2 and Arducopter 2.6 software.
Thank you for your ass
Read more…We finally got days with less than hurricane level winds (sorry quad rodeo people! The wind gave Jason quite a workout that day!) so I setup some mission runs at a nice field nearby. I have had good luck with 2.6 on my apm2 quad, so I setup a fair
Read more…I noticed that the Remzibi OSD is still showing it is unsupported with APM2 in the 3DR online store. Does anyone know whether this is likely to change soon? It offers more features than the mini osd and it would be nice to get the output from the APM
Read more…Are the gimbal ports (A10 and A11) powered from the inoutmrailmor the output rail? I'm asking because I want to power the APM2 with a separate battery on the input rail (through a 5v BEC) and I'm worried that the camera servos might cause a brown-out
Read more…