I'm looking for anyone's experience using the Multiplex FunJet as a UAV platform. They have a new Ultra Fun Jet coming out soon with stronger Epalor foam and CF spars.
The main page has one pictured but I never hear anyone talking about using it?
A
Read more…Hello fellow DIYers. I have finally decided to act on my dream of creating a UAV, and I thought I'd start out by asking what is probably a often-asked question from beginners:
How do you remain in contact with a UAV when it isn't in line-of-sight? (Fo
I am using this Tx/Rx:
I am having trouble with some labview based aps. I have downloaded and installed the latest LV runtime drivers linked to in the Ardupilot manual. The latest GCS works fine. The older GS does,t work any more as well as the ardu-imu demo. I get an erro
Read more…hello
i wanna know if is possible to georeferencing photos with arduimu and a gps i mean
x,y,z and omega,phi, kappa.
if is possible how much is the accuarcy i can get.
Read more…
This post is just a chop from the product page here on Nitroplanes.com, but I needed stuff to put into the discussion so I knabbed their entire page!
I think for some this would work well as part of their GCS.
Joystick simulative flight system
1.The
My team and I ordered a GPS unit from DIYdrones (GS407) for replacement in our Ardupilot/Easystar setup (The first got trashed in an unfortunate meeting with a building at 100ft.) The unit was ordered to be Ardupilot compatible, and would not plug an
Read more…Hi,
Our (of my and my best friend) drone is almost ready to be shown to our teachers, we just need a li`l help with the code.
We are using ardupilot 2.4.6 with excellent results and we don`t have time to upgrade to 2.6 before the test flight with teac
Hey all,
Hello everbody,I am on my first drone project and i would like to know how do you people do to relay the rc Rx to the servo with a micrrocontroler ?my 18f runs on 32 mhz and the program that i have made to relay the rc rx would only be giving me 1.4
Read more…i want to ask regarding the ground station.first of all1)while we are giving GPS data input to the auto-pilot kit,will we have to give an input to the xstream zigbee for importing the data to the ground station.2)while we are transmitting data from u
Read more…Hey Guys- I need to connect this prop:
http://carancho.com/AeroQuad/store/index.php?main_page=product_info&cPath=8&products_id=29
to a motor with a 3mm shaft.
Can someone help me find an adapter that would help me accomplish this?
thanks-
I have the ArduPilot board and ArduIMU set up on a 4 channel Hawk Sky air frame. The issue I'm having is that when I switch to Stabilize or Fly-By-Wire mode, channel 4 (rudder) deflects to an extreme servo value. The rudder still responds, but the
Read more…Hey everyone,
Dear Sirs.Please give some autopilot complete set you must order to have:1. programmable route.2. information about the flight on the ground (telemetry).3. Video from the board on the ground.Please give any components (including transmitters and rece
Read more…I am learning how to work with the X-Y IR sensor and I have a neophyte question. I power the IR sensors from the receiver, with Vout~5V from the BEC. The same source powers ardupilot (I guess it is denoted Vcc in the schematic, assuming that no exter
Read more…Not sure this forums is the best spot for this question but I don't see a better one...
I've been doing some basic research so I can start working on a Drone once I complete my Thesis. I'm expecting to go with a quadrocopter variant since I don't ha
Read more…I have a dynam hawk sky and I want to know if anyone has any suggestions for a motor to use with the 20 amp ESC's that I have....I have been using the microjet v3 from graysonhobby, but so far, in the last 2 or 3 weeks, both have gone bad...Anyone?
Read more…Hi can anyone give me an indication on how much current the ardupilot and Arduimu pull? Rather stupidly, I don't have a current reading on my multimeter :(
