Hi,
I have nice setup of APM1 (2560) with Arduplane 2.40 in large flying wing. Plane is grounded for about a year now and I want to fly it again. It worked well, everything was set up well. I am little afraid that upgrade to latest firmware will brea
Read more…Had a crash a while ago, and broken an arm and a prop. The motor seemed ok.
Have since rebuilt, and have noticed a slight yaw when accelerating - especailly straight up. Also noticed some on/off vibes noises in my last video, and now tonight as well,
Read more…Hi,
How APM should be configured if you want to use only rudder/elevator (no ailerons) for steering the plane?
Read more…For some AUTO missions, failsafe needs to be disabled. When the mission prohibits heading towards home from any point (could hit a mountain) or is expected to fly beyond reliable control range. Even momentary RTL can be disruptive for aerial photo m
Read more…Having some weird behavior I hope someone will know about.I have an APM 2 on a quad that has been working fine. Took it out today and it won't initialize. Te board just sits with the amber LED flickering. If I plug in the USB cable from the PC, the b
Read more…Hi folks,
What happens if I have my FS set to Continue mission but I lose signal while flying normal stablise? Will it RTL?
Option 1 is RTL, option 2 is continue mission in auto but it is not clear in the wiki what will happen if I have option 2 but n
Read more…It seems that stabilize, and FBW-A modes drops nose, and loses altitude.
While AUTR and RTL works perfectly fine.
What can cause this ? - Arduplane 2.73
Read more…I tried to create a really powerful quad with HK components and an APM 2.5. It looks like I have created an unflyable monster:
The first flight attempts were a disaster. Upon just touching the throttle it jumped in the air and flipped on its back fast
Read more…Hi Everyone,
Just thought I'd share what seems like a hardware problem with one of my genuine 3DR 433 MHz Telemetry modules that appears to die after around two and a half minutes.
The sequence of events in the video is repeatable and is as follows:
Hi,
I bought a ARDUPILOT 1.X long time ago and now I buy new APM 2.5. I reuse wifi parts of ARDUPILO 1.X in particular xbee in plane. In that moment this part must make yourself from parts.
Well, when I connect this old part to the APM2.5 dosen't work
Hi allThis is primarily an Australian issue, but in the long term it will affect us allI took this photo in Melbourne today, and went in and asked if I could use this for professional press work.The salesman said yes, on the condition that I flew und
Read more…Been watching my first vid taken on the quad, and noticed something that I'd also seen on the ground in previous flights - when switching to alt hold, the engines cut completely off for a second or even 2, before spinning up again. This results in an
Read more…Hey guys i have an issue with my newly built octo, whenever I switch to loiter it cuts throttle and falls like a rock whist still leveling.
I need to know why it is behaving like this and how to fix it if anyone knows, i will also link the KMZ and log
Read more…So I've been flying RC3 for a few days now, and my quad is locked in on stabalize and will fly excellent missions. However, the climb rate between waypoints is very slow. Looking at the logs it will only climb at 100cm/s. There is reference to the
Read more…
I recently switched to the 9XR Radio with Orange RX modeule/ 9ch Reciever DSM2. (Previouly used 9X radio/ with 9ch RF Reciever)
I use an APM 2.5 on a bixler 1.1, with Arduplane v2.70 software.
When doing the intial radio calibration, while adjusting
Read more…If you have an old APM1 1280 that you still fly with ArduPlane, then this is your chance to ask that we keep support for it in the next release. We are now getting to the point where it is taking more effort to keep supporting this old board, and unl
Read more…I have an octo and am installing a gimbal using the wiki. I've done this before on quads but not with an octo.
http://code.google.com/p/arducopter/wiki/AC2_Camera
Since I'm using digital servos, I wanted to set to another channel since A10 and A11 are
Read more…I must to use Mission Planner without internet connexion. Could I Mission Planner with satellite images without internet connexion?. How?
Read more…Hey all,
I was wondering why APM developers do not think of incorporating more powerful processing units on the next generations of APMs. The hardware's already received a lot of attention (including myself).
Is it possible to do that, I don't see the
Read more…I have been flying now for a couple of months and doing really great. Anyway, lately I added a Power Module from 3DR to my setup to monitor the battery and whatnot levels. I have removed JP 1 like the wiki says that I need to do. I have been flying w
Read more…