Hi all,
I have two XBee Pro 9's (XB09-DP in X-CTU) and have been unable to get X-CTU to read either one as the correct XB09-DP. What tipped me off to this problem originally is that when connecting my entire setup to the Ground Station software all I
Read more…I recently purchased a video transmitter and can't figure out where to get plugs to fit it or what kind they are in order to make a wiring harness.
It is a four pin connector similar to a LiPo balancing connector but not the same.
I would really appr
Hello,
I have tested the IMU only two weeks all the components works fine, and after I dont know why,
only IDG 500 doesnt response as you can see on arducopter configurator (blue and red graph).
So I decide to remove the IDG 500 with my hot air solderin
What programming language is it programmed in and what do I need to program in to program for it?Thanks.
Read more…Dear Diy Drones community,I am unable to change the flight mode assignments (toggle switch assignments) using the CLI as when I move the rudder stick it moves the rudder. I have also made sure that the APM is in the ground mode.
Read more…Question:I would like to send aircraft attitude information via I2C to another arduino. Has anyone attempted this? If my understanding is correct (probably isn't) I could use the same I2C port as the magnetometer, and the call to send it would be in
Read more…
I was planning to get a cheap netbook to be brought to the field and adjust ardupilot gain settings and re-upload the sketch, was just wondering if there are any compatibility issues with Win CE which is the standard for most netbooks, thanks
Read more…Has anybody used the Ardustation with the latest version of APM and or ACM. I have never been able to use it as I think it uses an older Protocol and with the new Mavlink and no support for this in the Ardustation firmware what are my opptions. I kno
Read more…well i had downloaded HAPPY KILLMORE as well as ardupilot GCS.Earlier also i had submitted posts for it,but i didnt get the reply.Actually sir i m not a student and dont have great programing skills.i had read in happy killmore GCS page that it accep
Read more…I recently purchased this video transmitter and am trying to figure out what type of connector is between the transmitter and its input pigtail.
Does anyone know what this is and where I can buy some with wire leads?
I want to adapt it to my rc rig
Read more…I'm in the process of building an OSD using the MAX7456 chip which uses the SPI port, and had a thought regarding the Chip Select pin. The shared PG2/PJ2 pin is close to the existing SPI/ISP header, but requires you to solder SJ2. Instead, why not
Read more…
Good day guys, hope you can shed some light on this..
I think I blew the outputs of my APM. The mux led doesn't light up when I power it up through the the rc's ubec and it doesn't receive my rc input and the leds aren't that bright. However, if
Read more…HiI finally got the last few bits of my quadcopter in today's post ...Now everything is assembled and ready to go.But I would need some help / information with the following issues:- While doing the pre-flight check I realized, that I am not sure abo
Read more…I had 2 very successful flights yesterday. Altitude hold was great, and my aircraft hit all waypoints. However, when going from point to point, the plane did not go in a straight line. it made "S" turns. Does someone know the best way to correct this
Read more…Hi Folks New guy here. I have been all over this forum trying to find a topic for Nitro powered copters. Looking at the ardupilot-mega version 1.0 instruction "Setting up APM for your RC gear". It appears every thing will connect properly. I have two
Read more…This is a NewB question and , yes, I have searched Google and these forums for answers.
I would like to:
I'm trying to calibrate my compass offsets using xbees for the communication. Everytime I get the menu in the CLI it cuts off around line r
r - Reset to fa
And when I use c to do compass offsets it streams the numbers for about 15-30 seconds and then
Read more…Two frames, one APM/IMU and different results?Quad1: Aluminum based, Motors Turnigy 2217, ESC Turnigy Plush 25A, Battery 3000mah, 60cm MotorToMotor. Weight 1.3kgQuad2: Aluminum based, Motors Roxy 2827/35, ESC Turnigy Plush 25A, Battery 2600mah, 50cm
Read more…Me again...
I appreciate the patience and help that several of you have put out in my cries for FNG help.
I can't find any good info on why I was told that a IC engine quad rotor with collective pitch rotors would not be able to respond quickly enough
Read more…Hi, I'm doing a ArduIMU quadcopter with V2. I load Arduimu code without problems and HappyKillmore ArduimuTest is fine, but when I try the plate with a servo and transmitter receiver does nothing, no move to move the plate, and even when I move the l
Read more…