I just receive my Remzibi OSD 3DR and test it with Remzibi OSD software and GPS emulator, all works perfect with GPS emulator with FTDI cable.
But when I am using my Delorme Earthmate GPS (see below the model and pinout cable), this GPS is not recogni
Read more…Dear all, I'm new in this forum, so it may be I will ask something already discussed..
It is my intention to build an hexacopter and to equipe it with 2 digital cameras with infrared remote trigger.
The intention is to shot one picture per camera at ea
Read more…I want to find out if anybody is actually using this code to control their LED lighting? I am trying to work on a single, unified LED lighting program. I am thinking about deleting or completely hijacking Motor_LEDs.
I just wanted to know if that wi
Read more…Can any one say if there is any advantage of shifting the mounting the motors 180 Degs from where they are at the moment, I appreciate a change of prop is required but I have seen a few Quads / Hex's with this config and they explain that it's "Sligh
Read more…Rather than wait weeks on end for a USBasp programmer from HK, (for firmware upgrade for Turnigy 9x V2 to er9x ) I bought this one from Ebay http://cgi.ebay.co.uk/ws/eBayISAPI.d...E:L:OU:GB:1123
Thinking they are all the same . It has a 6pin out , Not
Read more…I'm starting this thread in order to begin a discussion on potential Governor systems for use with Arducopter.
Malcolm Churn started talking to me about it a few days ago and it seems like something that is worthwhile pursuing if the AC system is ever
Read more…Please can someone help ? which of these is the correct configuration for Octocopter at V2.4
http://code.google.com/p/arducopter/wiki/AC2_Multi
http://code.google.com/p/arducopter/wiki/AC2_Props_2
thanks
Read more…Hey everyone,
I was wondering if anyone out there could help me out or give me some suggestions to get my quad flying! I have searched and searched and run into a road block. Here are the details:
Frame: 3DR Quad
Motors: 880kv with frame bored out to ac
Read more…Hello,
When I configure my RC all 4 channels show the correct measurements when moving to the max positions, but when I move thr throttle it shows on the screen that channel 3 is moving but channel 5 is also moving simultaneously.
So when I go to Fli
Read more…Hi folks!
I've just got my APM2 set up with X-plane 9 and before I've made any changes to pid settings, I find that every plane I've flown will not snap to level when stabilize is activated. In fact, all of them climb, some more aggressive than other
Read more…Hello Everybody,
i have two questions which hopefully somebody can answer:
First question:
- If i have a PC and a TG9x with the ER9x- Ardupilot Firmware, is it possible to connect both the PC (Mission Planner) as well as the Remote Control (TG9x) to the
Read more…Hi,
I searched the documentation and could not find any mention of this:
The Xtreme Bee adapter board has a slider switch maked MST<-->SLV (I guess master/slave). So what is the right position?
Also, there's at least one solder jumper on the board mark
Read more…Hi all,
I have bought a MediaTek MT3329 GPS chip, very nice, and am using it with my Arduino Nano.
I am trying to set it to output the diydrones message message at 10Hz, 38400baud.
I believe the setup code should be:
Serial.begin(38400);
Serial.print("$PM
Read more…Does anyone know where I can get a gear like this, or what it's called? It's the black gear on the servo i'm looking for.
Setting up my jdrones hex copter and the motors on number 7 and 8 channel make a constant beeping at 4 beeps per second. The ECS guide advises throttle is not in lowest position even though it was. I then put throttle in top position and plugged the
Read more…I am newbie on autopilot, but I am flying FPV. I already do have an Remzibi 3DR OSD and NMEA GPS.
I am planning to buy a ArduPilot for using independently on one of my 3 RC models: electric 2m glider, 450 (electric) classic helicopter, electric boat.
M
Hello,
I'm new in the APM2 world, and I have some trouble between APM2 and my Futaba PPM Sum receiver.
I activated PPM sum on the board (solder between PPM and CH5 pads), but no luck with it, no way to get a valid signal.
Do you have a solution? I prefe
Read more…Hi,
Is there any way to disable the GPS on the daughterboard(without desoldering or changing the daughterboard), and still connect an external GPS and have APM 2.0 use that instead?
Read more…think best case scenario, level flight, only weak wind - flying automatic RTL
then the APM - for some reason reboots.
plane rolls 10deg and pitches 5deg. - blame it on wind or last position of control surfaces.
Is there any chance, it will manage to b
Read more…